- Electric Power Generation:
- C175-16 GEN SET (S/N: WYB1-UP)
- Engine:
- C175-16 (S/N: M6B1-UP; P6L1-UP)
- Off-Highway Truck/Tractor:
- 793F Series AC (S/N: B7C1-UP)
- 793F (S/N: B7B1-UP)
- 795F Series AC (S/N: JTL1-UP)
- 797F (S/N: LLM1-UP)
- 793F (S/N: B7B1-UP)
Introduction
Important Safety Information
 | |
| Illustration 1 | g02139237 |
Think Safety | |
European Union Compliant, CE marked
Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.
Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.
Do not operate or perform any lubrication, maintenance, or repair on this product until you have read and understood the Tool Operating Manual.
Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.
The hazards are identified by the Safety Alert Symbol and followed by a Signal Word such as "DANGER","WARNING", or "CAUTION". The Safety Alert "WARNING" label is shown below.
A non-exhaustive list of operations that may cause product damage are identified by "NOTICE" labels on the product and in this publication.
Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure, work method, or operating technique that is not recommended by Caterpillar is used, the operator must be sure that the procedures are safe. The operator must also be sure that the product will not be damaged or made unsafe by any unspecified procedures.
The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job.
When replacement parts are required for this product Caterpillar recommends using Caterpillar replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength, and material.
Literature Information
This manual contains safety information, operation instructions and maintenance information and should be stored with the tool group
Some photographs or illustrations in this publication may show details that can be different from your service tool. Guards and covers might have been removed for illustrative purposes.
Continuing improvement and advancement of product design might have caused changes to your service tool, which are not included in this publication.
Whenever a question arises regarding your service tool or this publication, consult Dealer Service Tools (DST) for the latest available information.
Safety Section
The Safety Section lists basic safety precautions.
Read and understand the basic precautions listed in the Safety section before operating or performing maintenance and repair on this service tool.
General Information Section
The General Information Section describes tooling functions and features. The section provides useful information on individual parts, additional tooling, and resources.
Operation Section
The Operation Section is a reference for the new operator and a refresher for the experienced operator.
Photographs and illustrations guide the operator through correct procedures for using the tool group.
Operating techniques outlined in this publication are basic. Skill and techniques develop as the operator gains knowledge of the service tool and the tools capabilities.
Maintenance Section
The Maintenance Section is a guide to tool inspection, cleaning, storage, and tool disposal
Service Parts Section
The Service Parts Section is a reference for parts identification and available part numbers.
323-1146 C175 Engine Lifting Bracket
Used to remove and install the C175 Engine.
 | |
| Illustration 2 | g02444120 |
European Union Compliant, CE Marked | |
General Safety
 | |
| Illustration 3 | g02448886 |
Operation
Refer to appropriate D&A Service Manual for mounting and lifting hardware and correct location of lifting points.
 | |
| Illustration 4 | g02448896 |
 | |
| Illustration 5 | g02448897 |
 | |
| Illustration 6 | g02448898 |
Inspection
Inspect prior to each use for nicks, burrs, dents, cracks, bends, or worn parts. If damage is found, discontinue use until inspected and released for use by an approved inspector at the dealership. Inspect annually by an approved inspector at the dealership. If damage is beyond repair, destroy the tool as scrap.
Do not use unless load identification markings are legible.
 | |
| Illustration 7 | g02448919 |
 | |
| Illustration 8 | g02448920 |
 | |
| Illustration 9 | g02448921 |
 | |
| Illustration 10 | g02448922 |
 | |
| Illustration 11 | g02448923 |
Tool Disposal
At the end of the operational life of the tool, destroy the tool and dispose of as scrap.