349F and 352F Excavators Machine System Specifications Caterpillar

Pump Lines (Main)

Usage:

352F-VG A9J

Show/hide table




Illustration 1	g02615736
Rear view

Show/hide table

Table 1
Specification for 330-2499 Control Lines Gp
Item	Qty	Part	Specification Description
1	1	148-8408 Plug As	Torque to 95.0 ± 104.5 N·m (70.1 ± 77.1 lb ft).
2	4	8T-4186 Bolt	Torque to 30 ± 7 N·m (266 ± 62 lb in).
3	4	7X-2456 Bolt	Torque to 80 ± 8 N·m (59 ± 6 lb ft).
4	2	096-4884 Locknut	Tighten locknut to 15.0 ± 1.5 N·m (132.8 ± 13.3 lb in), if pipe thickness is 2.4 mm (0.09 inch).
4	2	096-4884 Locknut	Tighten locknut to 22 ± 3 N·m (195 ± 27 lb in), if pipe thickness is more than 2.4 mm (0.09 inch).
5	4	170-8553 Bolt	Torque to 50 ± 10 N·m (37 ± 7 lb ft).
6	1	148-8354 Elbow As	Torque to 41.0 ± 45.5 N·m (30.2 ± 33.68 lb ft).

Show/hide table




Illustration 2	g02615756
View of area A

Show/hide table

Table 2
Item	Qty	Part	Specification Description
Tighten the clamps (7) by maintaining dimension as shown in Illustration 2.
B	-	-	Dimension for both sides is 10 ± 3 mm (0.4 ± 0.1 inch).
C	-	-	Dimension is 50 ± 5 mm (2.0 ± 0.2 inch).

Caterpillar Information System:

349F and 352F Excavators Machine System Specifications Check Valve (Return Lines)

Filtration Procedure for Rebuilt Engines {0680, 0768, 1000, 1300} Filtration Procedure for Rebuilt Engines {0680, 0768, 1000, 1300}

3406E and C15 Marine Engines Fuel Injector - Check

C7 Engines for Combat and Tactical Vehicles Severe Service Application

349F and 352F Excavators Hydraulic System Relief Valve (Counterweight Cylinder) - Test and Adjust

C7 Engines for Combat and Tactical Vehicles Grounding Stud - Inspect/Clean/Tighten

Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Machine Monitoring System Configuration

Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Grade Control Configuration

Contamination Control of Rebuilt Engines by Using a Particle Counting Process Patent Pending{1000, 1300} Contamination Control of Rebuilt Engines by Using a Particle Counting Process Patent Pending{1000, 1300}

2011/01/10 A New Waste Gate for the Turbocharger Is Now Being Used on the Certain C13 Industrial Engines {1052, 1053, 1057, 1940}

3500 Engines Engine Oil Sequence Valves - Remove and Install

349F and 352F Excavators Machine System Specifications Accumulator (Pilot)

349F and 352F Excavators Machine System Specifications Boom Cylinder Lines

Suggested Equipment Layouts {0374, 0729, 4150, 7000, 7950} Suggested Equipment Layouts {0374, 0729, 4150, 7000, 7950}

349F and 352F Excavators Machine System Specifications Stick Cylinder Lines

2011/01/10 A New Valve Bridge Is Available for Certain Commercial Engines {1102, 1123}

349F and 352F Excavators Machine System Specifications Control Valve (Auxiliary)

2011/01/10 A New Valve Bridge Is Available for Certain Truck Engines {1102, 1123}

C32 Generator Set Overhaul Considerations

349F and 352F Excavators Machine System Specifications Control Valve

3116 and 3126 Marine Engines Auxiliary Water Pump (Rubber Impeller) - Inspect

3516C Locomotive Engines Camshaft - Remove

3516C Locomotive Engines Camshaft - Install

349F and 352F Excavators Machine System Specifications Control Valve