Process for Setting Up the Work Tool
The process of setting up a work tool will need to take place when the following occurs:
- Installation of a new tool control system or modification of an existing tool control system
- Major modification to machine hardware
- Machine ECM has been flashed or replaced
When setting the machine up for a work tool system, the electro-hydraulic system must be first installed on the machine. Then the machine ECM must be programmed to recognize components and operations for proper operation of the work tool.
The different tool control systems can be identified by referring to Testing and Adjusting, "System Identification".
- Each tool control system depends on the physical installation of various valves and hydraulic lines. Installation of all the hydraulic components and lines must be first accomplished. A list of all tool control system components is shown in "Tool Control System Components".
- The machine ECM must be programmed to recognize the installed hydraulic components. Refer to "Tool Installation Procedure" for the procedure and parameter descriptions.
- The machine ECM must then be programmed to receive signals from the control inputs that are installed on the machine. Refer to "Control Installation Procedure" for the procedure and parameter descriptions.
- After completion of the Tool Installation and Control Installation, the operation parameters for the work tool need to be programmed. Refer to Testing and Adjusting, "Work Tool Parameter - Program" for the Tool Control System.
Note: To view the factory parameter settings for the work tools, refer to Testing and Adjusting, "Default Value of Work Tool Parameters" for the Tool Control System.
Tool Control System Components
Note: The different tool control systems can be identified by referring to Testing and Adjusting, "System Identification".
Show/hide table
| Hydraulic Control System Components | |||
| Name of Tool Control System | Combined Function - Hydraulic Control | Combined Function - Hydraulic Control (Medium Pressure) | One-Way / One or Two Pump - Hydraulic Control |
| Work Tool Application | Common | Multi-Processor | Hammer |
| Input Components | |||
| ATT pedal pressure switch | - | 1 | - |
| ATT pedal pressure sensor | 1 | 1 | 1 |
| Tool load pressure sensor | - | - | - |
| Boom up pressure sensor | 1 | 1 | 1 |
| Boom down pressure sensor | 1(1) | 1(1) | 1(1) |
| Stick in pressure sensor | 1 | 1 | 1 |
| Stick out pressure sensor | 1 | 1 | 1 |
| Swing pressure sensor | 1(2) | 1(2) | 1(2) |
| Output Components | |||
| Flow limit proportional reducing valve | 2(2) | 2(2) | 2(2) |
| ATT valve #1 extend side proportional reducing valve | 1 | 1 | 1 |
| ATT valve #1 retract side proportional reducing valve | 1 | 1 | - |
| ATT valve #2 extend side proportional reducing valve | 1 | 1 | 1 |
| ATT valve #2 retract side proportional reducing valve | 1 | 1 | - |
| ATT valve #3 extend side proportional reducing valve | - | - | - |
| ATT valve #3 retract side proportional reducing valve | - | - | - |
| ATT valve #4 extend side proportional reducing valve | - | - | - |
| ATT valve #4 retract side proportional reducing valve | - | - | - |
| Solenoid variable relief valve 1 (E-RV1) | 1 | 1 | - |
| Solenoid variable relief valve 2 (E-RV2) | 1 | 1 | - |
| Boom down proportional reducing valve | - | - | - |
| Stick in proportional reducing valve | - | - | - |
Show/hide table
| (1) | Installed on standard machines |
| (2) | Installed on standard machines except for 312E, 314E, and 313F machines |
Note: The different tool control systems can be identified by referring to Testing and Adjusting, "System Identification".
Show/hide table
| Electric Control System Components | ||||
| Tool Control System | Combined Function - Electric Control | One-Way / One or Two Pump - Electric Control | Two-Way / One Pump | Medium Pressure |
| Work Tool Application | Multi-Processor | Hammer | Thumb | Auxiliary Pump |
| Input Components | ||||
| ATT pedal pressure switch | - | - | - | - |
| ATT pedal pressure sensor | - | - | - | - |
| Tool load pressure sensor | 1(1) | - | - | - |
| Boom up pressure sensor | 1 | 1 | - | - |
| Boom down pressure sensor | 1(2) | 1(2) | 1(2) | - |
| Stick in pressure sensor | 1 | 1 | - | - |
| Stick out pressure sensor | 1 | 1 | - | - |
| Swing pressure sensor | 1(3) | 1(3) | 1(3) | - |
| Output Components | ||||
| Flow limit proportional reducing valve | 2(3) | 2(3) | - | - |
| ATT valve #1 extend side proportional reducing valve | 1 | 1 | 1 | - |
| ATT valve #1 retract side proportional reducing valve | 1 | - | 1 | - |
| ATT valve #2 extend side proportional reducing valve | 1 | 1 | 1 | |
| ATT valve #2 retract side proportional reducing valve | 1 | - | 1 | |
| ATT valve #3 extend side proportional reducing valve | - | - | - | 1 |
| ATT valve #3 retract side proportional reducing valve | - | - | - | 1 |
| ATT valve #4 extend side proportional reducing valve | - | - | - | - |
| ATT valve #4 retract side proportional reducing valve | - | - | - | - |
| Solenoid variable relief valve 1 (E-RV1) | 1 | - | - | - |
| Solenoid variable relief valve 2 (E-RV2) | 1 | - | - | - |
| Boom down proportional reducing valve | 1(1) | - | - | - |
| Stick in proportional reducing valve | 1(1) | - | - | - |
Show/hide table
| (1) | Not equipped on 312, 313, 314, 316, and 318 machines |
| (2) | Installed on standard machines |
| (3) | Installed on standard machines except for 312E, 314E, and 313F machines |
The following procedure will allow the user to program the electro hydraulic components into the machine ECM using the monitor.
- The "Home" screen of the monitor is displayed when the key switch for the machine is turned to the ON position. Press the "Menu" key to display the main menu options.
Show/hide table
Illustration 2 g02293918 - Use the arrows to select "Service Mode" from the "Main Menu". Press the OK key.
- Input the password "9992". Press the Enter key.
Note: The soft switch key pad can be used to enter the desired numbers.
Show/hide table
Illustration 3 g02294839 - Select "Configurations" from the "Service" menu. Press the OK key.
Show/hide table
Illustration 4 g02294840 - Select "Aux Hyd Attachment" from the "Configurations" menu. Press the OK key.
Note: Press the Save key on this screen to save the parameters to USB memory.
Show/hide table
Illustration 5 g02294841 - Use the arrow keys to highlight the parameter. Press the OK key to change the default value.
Show/hide table
Illustration 6 g02688883 - Use the arrow keys to change the value or designation of the parameter. Press the OK key to enter the change.
Note: Setting the "Machine Application" will automatically load all the factory parameter setting options for the tool control system that are listed below the "Machine Application" option.
Show/hide table
| |
| Illustration 1 | g02293413 |
Reference: To view the factory parameter settings for the tool control systems, refer to "Tool Installation Parameters".
Reference: Refer to"Control Installation Parameter Descriptions" for descriptions of each of the Tool Installation parameters that are available for the tool control system.
Cat Electronic Technician Procedure
The following procedure will allow the user to program the electro hydraulic components into the machine ECM using Cat Electronic Technician.
- Connect the Cat Electronic Technician to the diagnostic connector located behind the seat on the left side of the cab.
Show/hide table
Illustration 8 g02713758 - Start Cat Electronic Technician.
Show/hide table
Illustration 9 g02713761 - Select the ECM for "Machine Control".
Show/hide table
Illustration 10 g02713773 - Select "Configuration" from the "Service"menu.
Show/hide table
Illustration 11 g02722663 - Expand the list for "Auxiliary Hydraulic Attachment Configurations". Highlight "Machine Application Configuration" and click on the "Change" button on the lower left corner.
Show/hide table
Illustration 12 g02722677 - Select the appropriate "Machine Application" for the machine. Press OK to enter the change.
Note: Setting the "Machine Application" will automatically load all the factory parameter setting options for the tool control system that are listed below the "Machine Application" option.
Show/hide table
| |
| Illustration 7 | g02713701 |
|
Diagnostic connector for Cat Electronic Technician | |
Reference: To view the factory parameter settings for the tool control systems, refer to "Tool Installation Parameters".
Reference: Refer to"Control Installation Parameter Descriptions" for descriptions of each of the Tool Installation parameters that are available for the tool control system.
Note: The different tool control systems can be identified by referring to Testing and Adjusting, "System Identification".
Show/hide table
| Hydraulic Control Systems - Tool Installation Parameter Settings | ||||
| Parameter Description | Combined Function - Hydraulic Control | Combined Function - Hydraulic Control (Medium Pressure) | One-Way / One or Two Pump - Hydraulic Control | |
| 1 | "Machine Application" | "Common - Hydraulic" | "Multi-Proc - Hydraulic" | "Hammer - Hydraulic" |
| 2 | "Attachment Valve #1" | One Way or Two Way - Pump #1 | One Way or Two Way - Pump #1 | One Way - Pump #1 |
| 3 | "Attachment Valve #2" | One Way or Two Way - Pump #2 | One Way or Two Way - Pump #1 | One Way - Pump #2 |
| 4 | "Attachment Valve #3" | Not Installed | Attachment Pump Valve - Two Way | Not Installed |
| 5 | "Attachment Valve #4" | Not Installed | Not Installed | Not Installed |
| 6 | "Attachment Valve #1 Type" | Hydraulic with Electrical Assist | Hydraulic with Electrical Assist | Hydraulic with Electrical Assist |
| 7 | "Attachment Valve #2 Type" | Hydraulic with Electrical Assist | Hydraulic with Electrical Assist | Hydraulic with Electrical Assist |
| 8 | "Attachment Valve #3 Type" | Hydraulic | Hydraulic | Hydraulic |
| 9 | "Attachment Valve #4 Type" | Hydraulic | Hydraulic | Hydraulic |
| 10 | "Atch Valve #1 Combiner" | Valve #2 Combined with Valve #1 | Valve #2 Combined with Valve #1 | Valve #2 Combined with Valve #1 |
| 11 | "Variable Relief Valve #1" | Installed on Valve #1 Extend port | Installed on Valve #1 Extend port | Not Installed |
| 12 | "Variable Relief Valve #2" | Installed on Valve #1 Retract port | Installed on Valve #1 Retract port | Not Installed |
| 13 | "F2 Load Pressure Sensor" | Not Installed | Not Installed | Not Installed |
| 14 | "Flow Limit Func Enable" | Enabled | Enabled | Enabled |
| 15 | "Boom Cyl Ret Speed Limit" | Not Installed | Not Installed | Not Installed |
| 16 | "Stick Cyl Ext Speed Limit" | Not Installed | Not Installed | Not Installed |
| 17 | "Multi Ope Atch Valve Limit" | Installed | Installed | Installed |
| 18 | "Atch Pedal #1 Press Sens" | Installed on Valve #1 | Installed on Valve #1 | Installed on Valve #1 |
| 19 | "Atch Pedal #2 Press Sens" | Not Installed | Not Installed | Not Installed |
Note: The different tool control systems can be identified by referring to Testing and Adjusting, "System Identification".
Show/hide table
| Electric Control Systems - Tool Installation Parameter Settings | |||||
| Parameter Description | Combined Function - Electric Control | One-Way / One or Two Pump - Electric Control | Two-Way / One Pump | Medium Pressure | |
| 1 | "Machine Application" | "Multi-Proc - Electrical" | "Hammer - Electrical" | "Thumb" | "Auxiliary Pump - Electrical" |
| 2 | "Attachment Valve #1" | One Way or Two Way - Pump #1 | One Way - Pump #1 | Two Way - Pump #1 | Not Installed |
| 3 | "Attachment Valve #2" | One Way or Two Way - Pump #2 | One Way - Pump #2 | Two Way - Pump #2 | Not Installed |
| 349E
Not Installed |
|||||
| 4 | "Attachment Valve #3" | Attachment Pump Valve - Two Way | Not Installed | Not Installed | Attachment Pump Valve - Two Way |
| 5 | "Attachment Valve #4" | Not Installed | Not Installed | Not Installed | Not Installed |
| 6 | "Attachment Valve #1 Type" | Electrical | Electrical | Electrical | Hydraulic |
| 7 | "Attachment Valve #2 Type" | Electrical | Electrical | Electrical | Hydraulic |
| 8 | "Attachment Valve #3 Type" | Electrical | Hydraulic | Hydraulic | Electrical |
| 9 | "Attachment Valve #4 Type" | Hydraulic | Hydraulic | Hydraulic | Hydraulic |
| 10 | "Atch Valve #1 Combiner" | Valve #2 Combined with Valve #1 | Valve #2 Combined with Valve #1 | Valve #2 Combined with Valve #1 | Not Installed |
| 11 | "Variable Relief Valve #1" | Installed on Valve #1 Extend port | Not Installed | Not Installed | Not Installed |
| 12 | "Variable Relief Valve #2" | Installed on Valve #1 Retract port | Not Installed | Not Installed | Not Installed |
| 13 | "F2 Load Pressure Sensor" | 349 - 320
Installed on Valve #1 |
Not Installed | Not Installed | Not Installed |
| 319 - 311
Not Installed |
|||||
| 14 | "Flow Limit Func Enable" | Enabled | Enabled | Disabled | Disabled |
| 15 | "Boom Cyl Ret Speed Limit" | 349 - 320
Installed |
Not Installed | Not Installed | Not Installed |
| 319 - 311
Not Installed |
|||||
| 16 | "Stick Cyl Ext Speed Limit" | 349 - 320
Installed |
Not Installed | Not Installed | Not Installed |
| 319 - 311
Not Installed |
|||||
| 17 | "Multi Ope Atch Valve Limit" | Installed | Installed | Not Installed | Not Installed |
| 18 | "Atch Pedal #1 Press Sens" | Not Installed | Not Installed | Not Installed | Not Installed |
| 19 | "Atch Pedal #2 Press Sens" | Not Installed | Not Installed | Not Installed | Not Installed |
Tool Installation Parameter Descriptions
Show/hide table
| Tool Installation Parameter Descriptions | ||||
| # | Cat ET Name | Monitor Name | Description | Purpose / Explanation |
| 1 | Machine Application Configuration | "Machine Application" | General tool setting | If the desired item were once selected among the previously defined names of tool control system, the settings here after are automatically updated to the defined settings. Also, setting here after could be changed individually. |
| 2 | Attachment Valve #1 Configuration | "Attachment Valve #1" | Installation setting of ATT valve #1 l | Operation setting of ATT valve #1 and driving pump is set. For stackable valve (F2.2):
When 1WAY alone is used, select "ONE WAY" When 2WAY alone is used, select "TWO WAY" When switching 1WAY/2WAY, select "ONE or TWO WAY". Set drive pump (Pump#1) and idler pump (Pump#2), respectively. When ATT pump is used. Select "Attachment Pump Valve" When 1WAY alone is used, select "ONE WAY" When 2WAY alone is used, select "TWO WAY" When switching 1WAY/2WAY, select "ONE or TWO WAY". |
| 3 | Attachment Valve #2 Configuration | "Attachment Valve #2" | Installation setting of ATT valve #2 | Operation setting of ATT valve #2 and driving pump is set. Setting procedure is similar as ATT #1. |
| 4 | Attachment Valve #3 Configuration | "Attachment Valve #3" | Installation setting of ATT valve #3 | Operation setting of ATT valve #3 and driving pump is set. Setting procedure is similar as ATT #1. |
| 5 | Attachment Valve #4 Configuration | "Attachment Valve #4" | Installation setting of ATT valve #4 | Operation setting of ATT valve #4 and driving pump is set. Setting procedure is similar as ATT #1. |
| 6 | Attachment Valve #1 Control Type Configuration | "Attachment Valve #1 Type" | Control method of ATT valve #1 | Set control method of ATT valve #1.
Hydraulic pilot method "HYDRAULIC" Electric pilot method "ELECTRICAL" Hydraulic pilot + Electric control method: Select "HYDRAULIC WITH ELECTRICAL ASSIST" |
| 7 | Attachment Valve #2 Control Type Configuration | "Attachment Valve #2 Type" | Control method of ATT valve #2 | Set control method of ATT valve #2. Setting procedure is similar as ATT #1. |
| 8 | Attachment Valve #3 Control Type Configuration | "Attachment Valve #3 Type" | Control method of ATT valve #3 | Set control method of ATT valve #3. Setting procedure is similar as ATT #1 |
| 9 | Attachment Valve #4 Control Type Configuration | "Attachment Valve #4 Type" | Control method of ATT valve #4 | Set control method of ATT valve #4. Setting procedure is similar as ATT #1. |
| 10 | Attachment Valve Combiner Configuration | "Atch Valve #1 Combiner" | Installation setting of 2 pump combined flow piping | Set necessity of combined pump flow piping of ATT valve #1 and ATT valve #2. "INSTALLED" is selected when combined flow piping is provided. "NOT INSTALLED" is selected when restricted in one pump flow operation. |
| 11 | Variable Relief Valve #1 Configuration | "Variable Relief Valve #1" | Installation setting of solenoid variable relief valve #1 | Setting of location of ATT valve to install solenoid variable relief valve #1, and the installing line. Ext: Extend side, Ret: Retract side. |
| 12 | Variable Relief Valve #2 Configuration | "Variable Relief Valve #2" | Installation setting of solenoid variable relief valve #2 | Setting of location of ATT valve to install solenoid variable relief valve #2, and the installing line. Ext: Extend side, Ret: Retract side. |
| 13 | F2 Type Valve Load Sense Pressure Sensor Installation Status | "F2 Load Pressure Sensor" | Installation setting of tool load pressure sensor | Establish a line where ATT valve is located to install tool load pressure sensor for enhancement of synchronous operation. |
| 14 | Main Pump Flow Limit Function Enable Status | "Flow Limit Func Enable" | Setting of Enabled/Disabled of tool flow limitation | When making a flow limitation by installing flow limit proportional reducing valve, flow of main pump could be restricted in accordance with the setting of "TOOL PROGRAM" described later if "INSTALLED" is set. |
| 15 | Boom Cylinder Retract Speed Limit System Installation Status | "Boom Cyl Ret Speed Limit" | Installation setting of boom down speed limit function | If "INSTALLED" is set when component necessary for boom DOWN speed limit function are installed, boom DOWN speed can be adjusted according to setting of "TOOL PROGRAM" described later. |
| 16 | Stick Cylinder Extend Speed Limit System Installation Status | "Stick Cyl Ext Speed Limit" | Installation setting of stick in speed limit function | If "INSTALLED" is set when component necessary for stick IN speed limit function are installed, stick IN speed can be adjusted according to setting of "TOOL PROGRAM" described later. |
| 17 | Enhanced Multiple Operation Attachment Valve Limit Installation Status | "Multi Ope Atch Valve Limit" | Installation setting of enhanced multi-function | If "INSTALLED" is set when component necessary for enhanced multi-function are installed, synchronous operation could be improved according to setting of "TOOL PROGRAM" described later. |
| 18 | Attachment Pedal #1 Pilot Pressure Sensor Installation Status | "Atch Pedal #1 Press Sens" | Installation setting of spool shift pressure sensor of ATT pedal #1 | Establish a line where ATT valve is located to install spool shift pressure sensor of ATT pedal #1 is set. |
| 19 | Attachment Pedal #2 Pilot Pressure Sensor Installation Status | "Atch Pedal #2 Press Sens" | Installation setting of spool shift pressure sensor of ATT pedal #2 | Establish a line where ATT valve is located to install spool shift pressure sensor of ATT pedal #2 is set. |
Control Installation Procedure
The following procedure will allow the user to program the electric or hydraulic controls that will be used to control the work tool into the machine ECM using the monitor.
Since control inputs are based on work tool applications and operator preference, these inputs are not defined by tool control system. Refer to "Control Installation Parameter Descriptions"to determine which controls are installed on the machine.
- The "Home" screen of the monitor is displayed when the key switch for the machine is turned to the ON position. Press the "Menu" key to display the main menu options.
Show/hide table
Illustration 14 g02293918 - Use the arrows to select "Service Mode" from the "Main Menu". Press the OK key.
- Input the password "9992". Press the Enter key.
Note: The soft switch key pad can be used to enter the desired numbers.
Show/hide table
Illustration 15 g02294839 - Select "Configurations" from the "Service" menu. Press the OK key.
Show/hide table
Illustration 16 g02294953 - Select "Control Inputs" from the "Configurations" menu. Press the OK key.
Note: Press the Save key on this screen to save the parameters to USB memory.
Show/hide table
Illustration 17 g02294954 - Use the arrow keys to highlight the parameter. Press the OK key to change the default value.
Show/hide table
Illustration 18 g02294956 - Use the arrow keys to change the value or designation of the parameter. Press the OK key to enter the change.
Show/hide table
|
| |
| Illustration 13 | g02293413 |
Reference: Refer to"Control Installation Parameter Descriptions" for descriptions of each of the Tool Installation parameters that are available for the tool control system.
Cat Electronic Technician Procedure
The following procedure will allow the user to program the electric or hydraulic controls that will be used to control the work tool into the machine ECM using the Cat Electronic Technician.
Since control inputs are based on work tool applications and operator preference, these inputs are not defined by tool control system. Refer to "Control Installation Parameter Descriptions"to determine which controls are installed on the machine.
- Connect the Cat Electronic Technician to the diagnostic connector located behind the seat on the left side of the cab.
Show/hide table
Illustration 20 g02713758 - Start Cat Electronic Technician.
Show/hide table
Illustration 21 g02713761 - Select the ECM for "Machine Control".
Show/hide table
Illustration 22 g02713773 - Select "Configuration" from the "Service"menu.
Show/hide table
Illustration 23 g02722684 - Expand the list for "Control Input Installations and Configurations". Highlight the parameter to change and click on the "Change" button on the lower left corner.
Show/hide table
Illustration 24 g02722688 - Select the appropriate "Control Input" for the controls installed on the machine. Press OK to enter the change.
Show/hide table
|
| |
| Illustration 19 | g02713701 |
|
Diagnostic connector for Cat Electronic Technician | |
Reference: Refer to "Control Installation Parameter Descriptions" for descriptions of each of the Tool Installation parameters that are available for the tool control system.
Control Installation Parameter Descriptions
Show/hide table
| Control Installation Parameter Descriptions | |||
| Cat ET Name | Monitor Name | Description | Explanation |
| Joystick Handle Configuration | "JOYSTICK HANDLE" | Type of joystick handle | Set type of joystick handle installed on the machine.
Type of handle: "Basic Handle": Lever installed on the standard machine "Joystick Switch": Lever with 4 buttons on standard lever "Modulation Handle": Lever with thumb wheel and 3 buttons |
| Foot Switch Installation Status | "Foot Switch" | Installation setting of foot switch | Set installation condition of foot switch. |
| Left Attachment Pedal Installation Status | "Left Attachment Pedal" | Installation setting of left ATT pedal | Set installation condition of left ATT pedal. |
| Right Attachment Pedal Installation Status | "Right Attachment Pedal" | Installation setting of right ATT pedal | Set installation condition of right ATT pedal. |
| Left Joystick Switch #1 Control Mode | "Left Joystick Switch #1" | Operating target of left joystick switch #1 | Set ATT valve and switching operation to be operated by left joystick switch #1.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. If the handle type is "Basic Handle", then setting is not required. |
| Left Joystick Switch #2 Control Mode | "Left Joystick Switch #2" | Operating target of left joystick switch #2 | Set ATT valve and switching operation to be operated by left joystick switch #2.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. If the handle type is "Basic Handle", then setting is not required. |
| Left Joystick Switch #4 Control Mode | "Left Joystick Switch #4" | Operating target of left joystick switch #4 | Set ATT valve and switching operation to be operated by left joystick switch #4.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. Handle is limited to "Joystick Switch" alone. |
| Right Joystick Switch #1 Control Mode | "Right Joystick Switch #1" | Operating target of right joystick switch #1 | Set ATT valve and switching operation to be operated by right joystick switch #1.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. If the handle type is "Basic Handle", then setting is not required. |
| Right Joystick Switch #2 Control Mode | "Right Joystick Switch #2" | Operating target of right joystick switch #2 | Set ATT valve and switching operation to be operated by right joystick switch #2.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. If the handle type is "Basic Handle", then setting is not required. |
| Right Joystick Switch #4 Control Mode | "Right Joystick Switch #4" | Operating target of right joystick switch #4 | Set ATT valve and switching operation to be operated by right joystick switch #4.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. Handle is limited to "Joystick Switch" alone. |
| Foot Switch Control Mode | "Foot Switch Control Mode" | Operation target of foot switch | Set ATT valve and switching operation to be operated by foot switch.
"Momentary" is selected to press and hold the switch for tool activation. "Toggled" is selected to press for tool activation ON and press again for tool activation OFF. |
| Left Joystick Thumbwheel Control Mode | "Left Joystick Thumbwheel" | Operating target of left modulation | Set ATT valve to be operated by left thumb wheel.
Handle is limited to "Modulation Handle" alone. |
| Right Joystick Thumbwheel Control Mode | "Right Joystick Thumbwheel" | Operating target of right modulation | Set ATT valve to be operated by right thumb wheel.
Handle is limited to "Modulation Handle" alone. |
| Left Attachment Pedal Forward Control Mode | "Left Atch Pedal Forward" | Operating target of push forward by foot of left ATT pedal | Set ATT valve to be operated by left ATT pedal push forward by foot.
Setting is available only when left ATT is made set of installation. |
| Left Attachment Pedal Rearward Control Mode | "Left Atch Pedal Rearward" | Operating target of push backward by foot of left ATT pedal | Set ATT valve to be operated by left ATT pedal push backward by foot.
Setting is available only when left ATT is made set of installation. |
| Right Attachment Pedal Forward Control Mode | "Right Atch Pedal Forward" | Operating target of push forward by foot of right ATT pedal | Set ATT valve to be operated by right ATT pedal push forward by foot.
Setting is available only when right ATT is made set of installation. |
| Right Attachment Pedal Rearward Control Mode | "Right Atch Pedal Rearward" | Operating target of push backward by foot of right ATT pedal | Set ATT valve to be operated by right ATT pedal push backward by foot.
Setting is available only when right ATT is made set of installation. |
Joysticks with Modulation Switches
Show/hide table
| |
| Illustration 25 | g03413046 |
|
(1) Left Hand Joystick
(2) Left Hand Joystick Switch 1 (3) Left Hand Joystick Thumbwheel (4) Left Hand Joystick Switch 2 (5) Right Hand Joystick (6) Right Hand Joystick Switch 1 (7) Right Hand Joystick Thumbwheel (8) Right Hand Joystick Switch 2 | |
Work Tool Setup - Additional Information
Error code E1132 is for "Inconsistent Configuration" of the Tool Control System. This code will be generated when the "Machine Application" parameter does not match what the machine ECM detects for tool system hardware installed on the machine.
In some instances, it occurs when the machine ECM is looking for the pressure sensor used with the control configuration "Hydraulic Foot Pedal with Electric Assist". In order to properly troubleshoot this sensor, check to ensure the machine configuration for the proper "Machine Application" parameter and the control configurations. If the machine is configured correctly, make sure that the hydraulic pedal pressure sensor is properly grounded.
E3579 and E3580 Code Troubleshoot
These codes are for "Bypass Cut Valves #1 and #2". These valves are not used for any E-Series Tool Control Systems and should always be set as "Not Installed."
These codes can also occur if "Heavy Attachment Control Feature" is set to "Installed". This function is not used in the E-Series Tool Control Systems and should always be set as "Not Installed".
This code can occur if "Hammer Automatic Control Feature" is set as "Installed". This feature is not used in the E-Series Tool Control Systems and should always be set as "Not Installed".
Caterpillar Information System:
2010/11/30 A New Muffler Assembly Prevents Exhaust Gas Recirculation on Certain 345D Excavators and Mobile Hydraulic Power Units {1062}
C27 and C32 Industrial Engines Engine Oil Filter Base - Remove and Install
2010/11/29 Retrofitting for Ultra Lean Burn on a G3516 Engine {1000, 775E}
C15 and C18 Engines Safety Messages
349F and 352F Excavators Hydraulic System Work Tool Parameter - Program
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Work Tool - Select
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System System Identification
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter - With Water Separator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
2010/10/20 A New Rocker Shaft Bolt Is Used on Certain C15 and C18 Engines {1102, 7553}
G3520E Generator Set Engines Configuration Parameters
3516C Locomotive Engines Exhaust Manifold - Remove and Install
C15 and C18 Engines Belts - Inspect/Replace - If Equipped
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Setting
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Adjustment
C13 and C15 On-highway Engines Engine Shutdown Occurs Intermittently
C27 Generator Set Plate Locations and Film Locations
C15 and C18 Tier 4 Final Engines ARD Fuel System - Flush
2010/10/18 A New Bushing Is Used for Front Gear Train Adapters in C175-16 Generator Set Engines {1151, 1162, 1206, 7551}
320 VH and VM Variable Gauge Undercarriage Undercarriage Cylinder (Adjustable Gauge) - Remove and Install - VM Undercarriage
320 VH and VM Variable Gauge Undercarriage Undercarriage Frame (Adjustable Gauge) - Remove and Install - VM Undercarriage
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System System Schematic
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System Output Components