A New Muffler Assembly Prevents Exhaust Gas Recirculation on Certain 345D Excavators and Mobile Hydraulic Power Units {1062}
- Excavator:
- 345D (S/N: BYC1-UP; RGD1-UP; RAE1-UP; YEE1-UP; NEG1-UP; EEH1-UP; RAJ1-UP; MLK1-UP; NLM1-UP; PBT1-UP)
- Mobile Hydraulic Power Unit:
- 345D MHPU (S/N: P5D1-UP)
The tail pipe has been shortened for the machines that are listed above. The shorter tail pipe prevents muffler exhaust gasses from recirculating inside the engine compartment. The longer tail pipe is too long and generates high air pressure in the ejector allowing exhaust gas and soot to recirculate into the engine room. The units without the noise regulatory requirement have been redesigned. The tail pipe of the muffler is shortened 100 mm (3.94 inch) from the current size to eliminate recirculation of exhaust gas to the engine room.
Show/hide table
Former Part Number     | Part Name     | New Part Number     |
---|---|---|
310-9618     | Muffler As     | 239-6580     |
Show/hide table
Effectivity and Adaptability of Shorter Tail Pipe     | ||
---|---|---|
Model     | Effectivity     | Adaptability     |
345D     | S/N:BYC152-UP     | S/N:BYC1-151     |
S/N:RGD150-UP | S/N:RGD1-149     | |
S/N:RAE152-UP | S/N:RAE1-151     | |
S/N:YEES/N:605Up | S/N:YEE1-604     | |
S/N:NEG504-UP | S/N:NEG1-503     | |
S/N:EEH946-UP | S/N:EEH1-945     | |
S/N:RAJ372-UP | S/N:RAJ1-371     | |
S/N:MLK184-UP | S/N:MLK1-183     | |
S/N:NLM237-UP | S/N:NLM1-236     | |
S/N:PBT436-UP | S/N:PBT1-435     | |
345D MHPU     | S/N:P5D159-UP     | S/N:P5D1-158     |
Caterpillar Information System:
C27 and C32 Industrial Engines Engine Oil Filter Base - Remove and Install
2010/11/29 Retrofitting for Ultra Lean Burn on a G3516 Engine {1000, 775E}
C15 and C18 Engines Safety Messages
349F and 352F Excavators Hydraulic System Work Tool Parameter - Program
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Work Tool - Select
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System System Identification
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter - With Water Separator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
2010/10/20 A New Rocker Shaft Bolt Is Used on Certain C15 and C18 Engines {1102, 7553}
G3520E Generator Set Engines Configuration Parameters
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Regulator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Process for Setting Up the Work Tool
3516C Locomotive Engines Exhaust Manifold - Remove and Install
C15 and C18 Engines Belts - Inspect/Replace - If Equipped
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Setting
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Adjustment
C13 and C15 On-highway Engines Engine Shutdown Occurs Intermittently
C27 Generator Set Plate Locations and Film Locations
C15 and C18 Tier 4 Final Engines ARD Fuel System - Flush
2010/10/18 A New Bushing Is Used for Front Gear Train Adapters in C175-16 Generator Set Engines {1151, 1162, 1206, 7551}
320 VH and VM Variable Gauge Undercarriage Undercarriage Cylinder (Adjustable Gauge) - Remove and Install - VM Undercarriage
320 VH and VM Variable Gauge Undercarriage Undercarriage Frame (Adjustable Gauge) - Remove and Install - VM Undercarriage
CX28 Transmission For Combat and Tactical Vehicles Transmission ; Transfer Case Electronic Control System System Schematic