Engine Oil Filter Base - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 185-3630 | Strap Wrench As | 1 |
- Use Tooling (A) to remove engine oil filters (4).
- Remove bracket (3)
- Remove bolts (1) and remove the engine oil filter base (2).
Show/hide table
Illustration 2 g02294238 Show/hide tablePersonal injury can result from parts and/or covers under spring pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
- Remove cover (5), gasket (6), springs (7) and plungers (8) from oil filter base (2).
Show/hide table
Illustration 1 | g02294113 |
- Install the engine oil filter base (2) in the reverse order.
- Apply clean engine oil to the oil filter seals prior to installation. Install the engine oil filters until the oil filter seal contacts the base, then turn the engine oil filters one full turn.
Caterpillar Information System:
2010/11/29 Retrofitting for Ultra Lean Burn on a G3516 Engine {1000, 775E}
C15 and C18 Engines Safety Messages
349F and 352F Excavators Hydraulic System Work Tool Parameter - Program
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Work Tool - Select
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System System Identification
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter - With Water Separator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
2010/10/20 A New Rocker Shaft Bolt Is Used on Certain C15 and C18 Engines {1102, 7553}
G3520E Generator Set Engines Configuration Parameters
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Regulator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust - Tool Relief Valve
2010/11/30 A New Muffler Assembly Prevents Exhaust Gas Recirculation on Certain 345D Excavators and Mobile Hydraulic Power Units {1062}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Process for Setting Up the Work Tool
3516C Locomotive Engines Exhaust Manifold - Remove and Install
C15 and C18 Engines Belts - Inspect/Replace - If Equipped
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Setting
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control: Parameter Adjustment
C13 and C15 On-highway Engines Engine Shutdown Occurs Intermittently
C27 Generator Set Plate Locations and Film Locations
C15 and C18 Tier 4 Final Engines ARD Fuel System - Flush
2010/10/18 A New Bushing Is Used for Front Gear Train Adapters in C175-16 Generator Set Engines {1151, 1162, 1206, 7551}
320 VH and VM Variable Gauge Undercarriage Undercarriage Cylinder (Adjustable Gauge) - Remove and Install - VM Undercarriage
320 VH and VM Variable Gauge Undercarriage Undercarriage Frame (Adjustable Gauge) - Remove and Install - VM Undercarriage