Procedure for Installing the 3N-8468 Clamp As on the Auxiliary Water Pump of Certain Marine Engines{1371}
- Generator Set:
- C18 (S/N: CYN1-UP; GEN1-UP)
- C32 (S/N: RNE1-UP; RNX1-UP)
- Marine Engine:
- 3406E (S/N: 9WR1-UP)
- 3412E (S/N: 9KS1-UP)
- C15 (S/N: RLA1-UP)
- C18 (S/N: WKB1-UP; PLE1-UP; CKH1-UP; C1J1-UP; JKX1-UP; J2K1-UP; T2P1-UP)
- C30 (S/N: CLX1-UP)
- C32 (S/N: RXB1-UP; RNC1-UP; RND1-UP; RNR1-UP; SLT1-UP; T3T1-UP; RNY1-UP; RNZ1-UP)
- 3412E (S/N: 9KS1-UP)
Introduction
Do not perform the procedure that is outlined in this Special Instruction until the entire instruction has been read and understood.
Installation Procedure
- Ensure that the clamps are installed in the correct orientation. Refer to Illustration 1 and Illustration 2 for the correct pump configuration and clamp orientation.
- Tighten the bolts evenly to a torque of 10 N·m (88.5 lb in).
Note: Tightening the bolts evenly will ensure an even clamp force across the mating flanges with putting stress on the clamps.
Show/hide table
Illustration 1 | g02216433 |
Pump example one (1) Clamps |
Show/hide table
Illustration 2 | g02216434 |
Pump example two (1) Clamps |
Caterpillar Information System:
C3.4B Engines System Overview
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System System Pressure - Release
C15 and C18 Tier 4 Final Engines Electronic Control System Components
C27 Petroleum Generator Set Engines Crankcase Pressure Is High
2010/09/14 Engine Oil Pump for C6.6 Engines {1304}
C7.1 Industrial Engine Clean Emissions Module
C15 and C18 Engines Monitoring System
C27 Petroleum Generator Set Engines Direct Fuel Control Mode - Test
C18 Marine Engine Sensors and Electrical Components - Engines With Less Than 1000 HP
C27 Petroleum Generator Set Engines Speed Control - Test
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
C27 Petroleum Generator Set Engines Diagnostic Trouble Codes
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Flashing Messages
C7.1 Industrial Engine ARD Fuel System - Flush - Clean Emissions Module
C7.1 Industrial Engine Diesel Particulate Filter - Clean
2010/10/06 A New Air Filter Change Indicator Group Is Used on C175-16 Generator Set {7452}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Components
C1.5 and C2.2 Industrial Engines Cold Weather Operation
C27 and C32 Industrial Engines Flywheel Housing - Remove and Install
G3304B and G3306B Engines Catalytic Converter Pressure - Test
C27 Petroleum Generator Set Engines Engine Monitoring Parameters
C27 Petroleum Generator Set Engines Switch Circuits - Test
G3304B and G3306B Engines Catalytic Converter Temperature - Test
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install