Flashing Messages
Messages are displayed in the information area of the display.
Show/hide table
|
Linkage elevation monitor is unavailable or needs ceiling or floor established again. |
Show/hide table
| Cat Grade Control Message | Problem | Solution |
|---|---|---|
| Check Machine Dimensions | The dimensions that were entered into the Cat Grade Control system is incomplete, or inconsistent with a machine dimension that can be measured by the system. | Contact your Caterpillar technical communicator for more information. |
| Check Linkage Measurements | The arm or linkage measurements are inconsistent with the Bucket PSC extension . | Verify bucket dimensions and contact your Caterpillar technical communicator for more information. |
| Check Body Sensor | The system cannot communicate with the body angle sensor, or the sensor is out of operating range. | Contact your Caterpillar technical communicator for more information. |
| Check Boom Sensor | The system cannot communicate with the boom POT position sensor, or the sensor is out of operating range | Contact your Caterpillar technical communicator for more information. |
| Check Stick Sensor | The system cannot communicate with the stick POT position sensor, or the sensor is out of operating range | Contact your Caterpillar technical communicator for more information. |
| Check Bucket Sensor | The system cannot communicate with the bucket position PSC sensor, or the sensor is out of operating range. | Contact your Caterpillar technical communicator for more information. |
| Check Tilt Bucket Sensor | The system cannot communicate with the bucket tilt sensor. | Contact your Caterpillar technical communicator for more information. |
| New Sensor Cycle Key Off | The system has detected a new tilt bucket angle sensor. | Turn off the machine, wait a minute, and start machine. |
Caterpillar Information System:
Procedure for Installing the 3N-8468 Clamp As on the Auxiliary Water Pump of Certain Marine Engines{1371} Procedure for Installing the 3N-8468 Clamp As on the Auxiliary Water Pump of Certain Marine Engines{1371}
C3.4B Engines System Overview
303.5E2 CR, 304E2 CR, 305E2 CR and 305.5E2 CR Mini Hydraulic Excavators Machine System System Pressure - Release
C15 and C18 Tier 4 Final Engines Electronic Control System Components
C27 Petroleum Generator Set Engines Crankcase Pressure Is High
2010/09/14 Engine Oil Pump for C6.6 Engines {1304}
C7.1 Industrial Engine Clean Emissions Module
C15 and C18 Engines Monitoring System
C27 Petroleum Generator Set Engines Direct Fuel Control Mode - Test
C18 Marine Engine Sensors and Electrical Components - Engines With Less Than 1000 HP
C27 Petroleum Generator Set Engines Speed Control - Test
Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120} Preventing Cracks and Leaks in the Composite Valve Covers on Some C9 Engines{1107, 1120}
C7.1 Industrial Engine ARD Fuel System - Flush - Clean Emissions Module
C7.1 Industrial Engine Diesel Particulate Filter - Clean
2010/10/06 A New Air Filter Change Indicator Group Is Used on C175-16 Generator Set {7452}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Components
C1.5 and C2.2 Industrial Engines Cold Weather Operation
C27 and C32 Industrial Engines Flywheel Housing - Remove and Install
G3304B and G3306B Engines Catalytic Converter Pressure - Test
C27 Petroleum Generator Set Engines Engine Monitoring Parameters
C27 Petroleum Generator Set Engines Switch Circuits - Test
G3304B and G3306B Engines Catalytic Converter Temperature - Test
C27 and C32 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
2010/09/14 Fuel Injection Timing Check for C0.5, C0.7, C1.1, 3011C, C1.5, 3013C, C1.6 , 3024C, 3024CT and C2.2 Engines {1251, 1290}