Air Inlet and Exhaust System - Inspect
应对进排气系统进行综合性目视检查。 确保系统中没有泄漏迹象。
如果进气系统或排气系统中存在阻塞,则发动机的性能就会降低。
- 检查发动机空气滤清器进气口和进气管道以确保通道没有被阻塞或压扁。
- 检查发动机空气滤清器滤芯。 用清洁的发动机空气滤清器滤芯更换脏的发动机空气滤清器滤芯。 有关正确的步骤,请参阅操作和保养手册, "发动机空气滤清器滤芯(双滤芯)- 清洁/更换"或操作和保养手册, "发动机空气滤清器滤芯(单滤芯)- 更换"。
- 检查发动机空气滤清器滤芯清洁的一侧有无灰尘的踪迹。 如果观察到灰尘的踪迹,说明污染物正流过发动机空气滤清器滤芯和/或发动机空气滤清器滤芯密封件。
Show/hide table
高温发动机部件可能导致灼伤。 进行发动机保养之前让发动机和部件冷却下来。 |
Show/hide table
接触正在运转的发动机会因热零件而导致灼伤或因旋转零件而导致伤害。 在旋转的发动机上工作时,避免接触热零件或旋转零件。 |
Show/hide table
图 1 | g02161629 |
典型示例 (1) 分离器 (2) 气门机构盖 (3) 呼吸器管 |
Show/hide table
图 2 | g02161630 |
典型示例 (4) 呼吸器管 (5) 通气孔组件 (6) 排气管 (7) 单向阀 (8) 出口 |
如果曲轴箱呼吸器滤清器堵塞,安全阀将工作。 如果系统中存在堵塞,安全阀也会工作。
应对曲轴箱呼吸器进行总体目视检查。 曲轴箱呼吸器安全阀工作时,可以观察到以下问题。 这些问题出现在呼吸器滤罐后面。
- 机油沾污
- 油滴
- 小块的油迹
- 检查发动机曲轴箱呼吸器的滤芯。 如有必要,更换曲轴箱呼吸器滤芯。 请参阅操作和保养手册, "发动机曲轴箱呼吸器滤芯 - 更换"。
- 如果滤罐中有油泥或碎屑,拆下滤罐。 请参阅拆解和组装, "曲轴箱通气孔 - 拆卸和安装"。 清洁滤罐内侧。 检查进气口、出气口接头以及回油口接头是否清洁。
- 拆下呼吸器软管,目视检查内侧有无堵塞迹象,检查有无低压空气。 如有必要,清洁软管。
- 如有必要,更换曲轴箱呼吸器滤芯。 请参阅操作和保养手册, "发动机曲轴箱呼吸器滤芯 - 更换"。
- 安装滤罐和软管。 请参阅拆解和组装, "曲轴箱通气孔 - 拆卸和安装"。
- 检查确认曲轴箱呼吸器出口清洁无堵塞。 在恶劣天气下,结冰会导致堵塞。
如果出现过大曲轴箱压力,但曲轴箱呼吸器安全阀未启用,则气门机构盖中可能存在堵塞。
- 拆下气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
- 检查气门室盖的内部有无碎屑。 必须检查盖内的油水分离器。 确保清除盖内的所有碎屑。
注: 不要试着从盖上拆下分离器。 分离器与盖相连时,可以对其进行清洁。
Caterpillar Information System:
C15 and C18 Engines Compression Brake - Inspect/Adjust/Replace
C13, C15, and C18 Tier 4 Interim Engines Cat ET Service Features
Idler Oil Fill Volume {4159, 4159} Idler Oil Fill Volume {4159, 4159}
C175 Generator Sets Varistor - Inspect
Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451} Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225} Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C175 Generator Sets Space Heater - Test
C175 Generator Sets Engine Valve Lash - Check
C175 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C175 Generator Sets Coolant Sample (Level 2) - Obtain
C175 Generator Sets Coolant Sample (Level 1) - Obtain
C4.4 Industrial Engine Valve Mechanism Cover
C27 and C32 Engines for Caterpillar Built Machines Electronic Control System Components
C9.3 Engines for Caterpillar Built Machines Unit Injector - Remove
Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451} Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451}
C15 and C18 Engines Grounding Stud - Inspect/Clean/Tighten
C15 and C18 Engines Valve Actuators - Check
C27 and C32 Tier 4 Engines Sensor Supply - Test
3516C Generator Sets Coolant (DEAC) - Change
3516C Generator Sets Coolant (ELC) - Change
3500 Generator Sets Coolant Extender (ELC) - Add
C9.3 Engines for Caterpillar Built Machines Unit Injector - Install
C175-16 Petroleum Generator Set Engines Coolant Level - Check