Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | −     | 导向螺栓 5/8 - 18 NF x 7 in     |
1     |
B     | 4C-5593     | 螺纹润滑剂     | −     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (1) 和护罩 (2) 。
Show/hide table
图 1 | g02160891 |
- 释放皮带张紧器上的张力后将皮带 (3) 放到一旁。
- 拆下螺栓 (4) ,然后拆下皮带轮 (5) 。
- 拆下螺栓 (6) 并安装工具 (A) 。
Show/hide table
图 2 | g02160924 |
- 拆下剩余的螺栓 (6) 。 由两人拆下减振器组件 (7) 。 减振器组件 (2) 的重量约为 46 kg (100 lb)。
- 拆下螺栓 (10) ,然后拆下间隔套 (9) 。
Show/hide table
图 3 | g02161096 |
- 将减振器 (7) 从转接接头 (8) 上分离。
安装步骤
- 按相反顺序安装减振器 (7) 。
- 将工具 (B) 涂抹在螺栓 (6) 上。
- 用 270 ± 40 N·m (200 ± 30 lb ft) 的扭矩拧紧螺栓 (6) 。
Caterpillar Information System:
C175 Generator Sets Space Heater - Test
C175 Generator Sets Engine Valve Lash - Check
C175 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C175 Generator Sets Coolant Sample (Level 2) - Obtain
C175 Generator Sets Coolant Sample (Level 1) - Obtain
C175 Generator Sets Coolant Level - Check
C175 Generator Sets Coolant Extender (ELC) - Add
C175 Generator Sets Coolant (ELC) - Change
C18 Marine Generator Set Overhaul (Major)
C18 Marine Generator Set Overhaul (Top End)
797F and 797F XQ Off-Highway Trucks Machine Systems Rear Axle Oil Cooler - Remove and Install
C175 Generator Sets Coolant (DEAC) - Change
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225} Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451} Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451}
C175 Generator Sets Varistor - Inspect
Idler Oil Fill Volume {4159, 4159} Idler Oil Fill Volume {4159, 4159}
C13, C15, and C18 Tier 4 Interim Engines Cat ET Service Features
C15 and C18 Engines Compression Brake - Inspect/Adjust/Replace
C4.4 Industrial Engine Air Inlet and Exhaust System - Inspect
C4.4 Industrial Engine Valve Mechanism Cover
C27 and C32 Engines for Caterpillar Built Machines Electronic Control System Components
C9.3 Engines for Caterpillar Built Machines Unit Injector - Remove
Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451} Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451}
C15 and C18 Engines Grounding Stud - Inspect/Clean/Tighten