Unit Injector - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A.     | 268-1968     | 撬杆     | 1     |
开始:
- 拆下气门机构盖。 请参阅拆解和组装, "气门机构盖 - 拆卸和安装"。
- 拆下喷油管。 请参阅拆解和组装, "燃油管 - 拆卸和安装"。
- 完全松开纬管螺母 (1) 。 从孔中拉出纬管 (1) ,直至看到 O 形密封圈 (2) 为止。 此操作将会确保在拆卸过程中喷油器不会接触到纬管。 此时,检查 O 形密封圈 (2) 有无磨损或损坏。 如果必要,更换 O 形密封圈。
Show/hide table
图 1 | g01264292 |
Show/hide table
图 2 | g01264293 |
注: 请勿拆下纬管。 此操作将会降低系统污染的风险。
- 从单体喷油器上断开线束组件 (3) 。
Show/hide table
图 3 | g02161166 |
典型示例 |
- 从卡箍 (6) 上拆下螺栓 (5) 。
Show/hide table
图 4 | g02161316 |
典型示例 |
- 如果无法用手拆下单体喷油器 (4) ,则转至步骤 5。
注: 可能的话,通过用手扭转喷油器并向上拉动拆下单体喷油器。 在拆卸过程中,要确保不要撞击单体喷油器。
- 将工具 (A) 放置到单体喷油器卡箍 (6) 的下面。 小心从缸盖上拆下单体喷油器 (4) 。
Show/hide table
图 5 | g02161361 |
典型示例 |
注: 在拆卸过程中,不要损坏单体喷油器。 侧向加载可能会损坏单体喷油器。
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Electronic Control System Components
C4.4 Industrial Engine Valve Mechanism Cover
C4.4 Industrial Engine Air Inlet and Exhaust System - Inspect
C15 and C18 Engines Compression Brake - Inspect/Adjust/Replace
C13, C15, and C18 Tier 4 Interim Engines Cat ET Service Features
Idler Oil Fill Volume {4159, 4159} Idler Oil Fill Volume {4159, 4159}
C175 Generator Sets Varistor - Inspect
Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451} Rework Procedure for the Connection of Speed Adjust Circuit to Control Panels on Certain C4.4Powered Generating Sets{7332, 7451}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225} Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C175 Generator Sets Space Heater - Test
C175 Generator Sets Engine Valve Lash - Check
Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451} Rework Procedure for the Connection of Engine Harness to Engine Interface Module (EIM) Fitted to Certain C2.2, C3.3, C4.4, and C6.6 Powered Generating Sets{1901, 7451}
C15 and C18 Engines Grounding Stud - Inspect/Clean/Tighten
C15 and C18 Engines Valve Actuators - Check
C27 and C32 Tier 4 Engines Sensor Supply - Test
3516C Generator Sets Coolant (DEAC) - Change
3516C Generator Sets Coolant (ELC) - Change
3500 Generator Sets Coolant Extender (ELC) - Add
C9.3 Engines for Caterpillar Built Machines Unit Injector - Install
C175-16 Petroleum Generator Set Engines Coolant Level - Check
3516C Generator Sets Coolant Sample (Level 1) - Obtain
G3516 Power Module Coolant Sample (Level 2) - Obtain
3516C Generator Sets Coolant Temperature Regulator - Replace