Cylinder Liner - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-8665 | Cylinder Liner Puller | 1 |
Start By:
- Remove the pistons and connecting rods.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining and filling procedures.
- Place covers over the crankshaft journals in order to shield the journals from dirt and coolant.
- Use Tooling (A) in order to remove the cylinder liner.
Show/hide table
Illustration 1 g01004731 - Remove O-ring seals (1) and filler band (3) from cylinder liner (2).
Caterpillar Information System:
3508, 3512 and 3516 Generator Set Engines Pistons and Connecting Rods - Install
3508, 3512 and 3516 Generator Set Engines Pistons and Connecting Rods - Remove
349F and 352F Excavators Joystick Controls Alternate Patterns
3508, 3512 and 3516 Generator Set Engines Piston Cooling Jets - Remove and Install
Replacement of High Pressure Fuel Lines on C7 On-highway Engines{1252, 1254} Replacement of High Pressure Fuel Lines on C7 On-highway Engines{1252, 1254}
C9.3 Engines for Caterpillar Built Machines Fuel Temperature Is High
797F and 797F XQ Off-Highway Trucks Machine Systems Power Converter (CAB) - Remove and Install
349F and 352F Excavators Cab Door
C9.3 Tier 4 Interim Engines Power Is Intermittently Low or Power Cutout Is Intermittent
C9.3 Tier 4 Interim Engines Fuel Pressure Is High
2010/01/25 Installing Orifice Plates in some G3520C Landfill Engines {1063, 1380}
349F and 352F Excavators Power Receptacle - If Equipped
3508, 3512 and 3516 Generator Set Engines Cylinder Liner - Install
2009/12/09 Fuel Injection Pump Gear on 3054C, C3.3, C6.6, C4.4 and C4.4 (Mech) Engines {1251, 1290}
2010/01/08 Fuel Injection Pump Gear on 3054C, C3.3, C6.6, C4.4 and C4.4 (Mech) Engines {1251}
793F Off-Highway Truck Machine Systems Magnetic Switch (Main Power) - Remove and Install
Installation of the Synchronization Module{4480} Installation of the Synchronization Module{4480}
793F Off-Highway Truck Machine Systems Display Module - Remove and Install
Track Servicing Equipment, Tooling, Literature, and Training Review {0374, 4169, 4170, 4171, 4172, 4174, 4175, 4176} Track Servicing Equipment, Tooling, Literature, and Training Review {0374, 4169, 4170, 4171, 4172, 4174, 4175, 4176}
793F Off-Highway Truck Machine Systems Electronic Control Module (Advisor) - Remove and Install - VIMS
C18 Generator Set Exciter - Remove and Install
3508, 3512 and 3516 Generator Set Engines Camshaft - Remove
C9.3 Tier 4 Final Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (ARD Combustion Air)