Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 238-9586 | Camshaft Drive Group | 1 |
B | 1P-0820 | Hydraulic Puller | 1 |
8B-7548 | Push-Puller Tool Group | 1 | |
8B-7559 | Adapter | 2 | |
5H-1504 | Hard Washer | 3 | |
9U-6600 | Hand Hydraulic Pump | 1 | |
C | 125-0200 | Camshaft Pilot As | 2 |
D | 125-0201 | Camshaft Guide As | 1 |
E | 8T-3169 | Crank Assembly | 1 |
Start By:
- Remove the rocker shaft and the pushrods.
- Remove the tachometer drive.
- Remove the governor drive.
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove covers (1).
Show/hide table
Illustration 2 g02045598 - Remove bolt (3) and the cap. Disconnect rod assembly (2) from the fuel control shaft.
Show/hide table
Illustration 3 g02045599 - Remove bolts (5). Remove lever assembly (4) and rod assembly (2) as a unit.
Show/hide table
Illustration 4 g02050814 - Remove cover (6) from the front housing.
Show/hide table
Illustration 5 g02050835 - Pull valve lifters (7) away from the camshaft. Hold valve lifters (7) in position with O-ring seals.
Show/hide table
Illustration 6 g02050873 - Remove covers (8) for the camshaft drive gears from the flywheel housing.
Show/hide table
Illustration 7 g02050875 - Remove the bolt and plate (9) that fastens camshaft drive gear (10) to the camshaft.
Show/hide table
Illustration 8 g02050877 - Place the three washers from Tooling (B) behind plate (9) and install the bolt.
Show/hide table
NOTICE Do not apply more than
51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at68900 kPa (10000 psi) . If too much pressure is applied, the gear may be damaged. - Install Tooling (B) on camshaft drive gear (10). Apply
51675 kPa (7500 psi) to Tooling (B). Strike the screw on Tooling (B) with a hammer until camshaft drive gear (10) is free from the camshaft. Remove Tooling (B) and camshaft drive gear (10).Show/hide tableIllustration 9 g02050934 - Remove bolts (11) and thrust washers (12) that fasten the camshaft to the engine block.
- Perform Steps 6 through 10 for the camshaft on the other side of the engine.
Show/hide table
Illustration 10 g02050937 - Install Tooling (C) on each end of the camshaft.
Note: Tooling (D) can be installed on the flywheel housing in order to remove the camshaft from the rear. Tooling (D) can also be installed on the front housing in order to remove the camshaft from the front of the engine.
- Install Tooling (D) on the flywheel housing.
- Install Tooling (E) on the end of Tooling (C).
Note: The following Step is for 3508 Engines.
Note: The weight of the camshaft for 3508 Engines is approximately
45 kg (100 lb) . The camshaft is one piece. - Rotate the camshaft with Tooling (E). Pull the camshaft out of the engine until a suitable lifting device can be attached. Remove the camshaft from the engine.
Note: The following Steps are for 3512 and 3516 Engines.
Note: The weight of the camshaft for 3512 Engines is approximately
64 kg (140 lb) . The weight of the camshaft for 3516 Engines is approximately82 kg (180 lb) . - Rotate the camshaft with Tooling (E). Pull the camshaft out of the engine until a suitable lifting device can be attached. Remove front camshaft (13) and rear camshaft (14) as a unit.
Show/hide table
Illustration 11 g02051018 - Remove bolts (15). Separate the camshafts and remove spacer (16).
- Remove the dowel from the front of the camshaft, if necessary.
- Repeat Steps 12 through 18 for the other camshaft.
Illustration 1 | g02045597 |