Center Arm (Steering) - Adjust
Show/hide table
图 1 | g02038320 |
转向总成的顶视图 (1) 机架转向机 (2) 中心臂 |
Show/hide table
图 2 | g02038416 |
转向总成的视图 A-A (1) 机架转向机 (3) 螺栓 (4) 轴承 (5) 轴承 (6) 螺栓 (7) 底板 (8) 轴承 (9) 触针 (10) 垫片 (11) 顶板 |
Show/hide table
图 3 | g02038432 |
转向总成的视图 B (C) 2 ± 0.5 mm (0.079 ± 0.02 in) |
Show/hide table
图 4 | g02038418 |
Show/hide table
图 5 | g02038456 |
视图 D-D (2) 中心臂 (3) 螺栓 (11) 顶板 |
Show/hide table
图 6 | g02044996 |
E-E 视图 (2) 中心臂 (6) 螺栓 (7) 底板 |
- 如果检测到中央臂 (2) 发生垂直移动,则必须垫补中央臂 (2) 。 使用以下步骤正确垫补中央臂 (2) 至机架转向机 (1) 。
- 确保中央臂 (2) 靠在机架转向机 (1) 的底部。
注: 请参阅转向系统规范, "转向连杆和油缸安装件",以选择适合的垫片组。
- 确保中央臂 (2) 靠在机架转向机 (1) 的底部。
- 按照以下步骤正确垫补中央臂 (2) 。
注: 请勿重复使用螺栓。
- 将轴承 (4) 和轴承 (8) 安装在机架转向机 (1) 上。
- 将轴承 (5) 安装在中央臂 (2) 中。
注: 参考图 2 查看轴承 (4) 、轴承 (8) 和轴承 (5) 的安装。
- 用 11 颗螺栓 (6) 和硬垫片安装板 (7) 。 O 形圈必须与板 (7) 一起安装。
注: 调整步骤期间,务必正确支撑中央臂 (2) 。
注: 两块板的安装将显示必须要垫补的间隙。
- 用八颗螺栓 (3) 和硬垫片安装板 (10) 。 O 形圈必须与板 (10) 一起安装。
- 根据需要在中央臂 (2) 和机架转向机 (1) 的顶部之间插入垫片 (10) 。
- 将螺栓 (6) 拧紧至扭矩 55 ± 10 N·m (40.6 ± 7.4 lb ft)。 拧紧螺栓 (3) 至 28 ± 7 N·m (20.7 ± 5.2 lb ft) 的扭矩。
注: 请参阅转向系统规范, "转向连杆和油缸安装件",以选择适合的垫片组。
- 拆下螺栓 (3 ) 。 拆下板 (10) 。 安装以上确定的垫片 (10) 。 再增加一块薄垫片。
注: 请勿在最终的垫片组中使用超过两块薄垫片。 如果需要三块薄垫片,用一块厚垫片替代三块薄垫片。
- 安装销 (9) 。
- 安装螺栓 (3) 、垫片和板 (10) 。
- 将螺栓拧紧至扭矩 28 ± 7 N·m (20.7 ± 5.2 lb ft)。
Caterpillar Information System:
UPSB130 Uninterruptible Power Supply Modes Of Operation
C9.3 Industrial Engine Soot Antenna
793F Off-Highway Truck Machine Systems Brake Control Valve (Service Brake, Parking Brake) - Assemble
793F Off-Highway Truck Machine Systems Brake Control Valve (Service Brake, Parking Brake) - Disassemble
G3304B and G3306B Engines Oxygen Level - Test
UPSB130 Uninterruptible Power Supply Glossary
UPSB130 Uninterruptible Power Supply Related Options
UPSB130 Uninterruptible Power Supply Component Location
UPSB130 Uninterruptible Power Supply UPS Characteristics
UPSB130 Uninterruptible Power Supply Battery Service
UPSB130 Uninterruptible Power Supply Return to Normal Operation
UPSB130 Uninterruptible Power Supply UPS Isolation
UPSB130 Uninterruptible Power Supply Walk-Around Inspection
Reuse and Salvage of 3208 Engine Sleeve Metering Fuel Systems (SMFS) {0374, 1250} Reuse and Salvage of 3208 Engine Sleeve Metering Fuel Systems (SMFS) {0374, 1250}
349F and 352F Excavators Stopping the Engine
C9.3 Tier 4 Interim Engines Fuel Pressure Is Low
349F and 352F Excavators Equipment Lowering with Engine Stopped
349F and 352F Excavators Operation Information
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (DPF Inlet)
2009/12/09 A New Undersized Connecting Rod Bearing Is Available for All C27 and C32 Engines {1225}
349F and 352F Excavators Power Receptacle - If Equipped
2010/01/25 Installing Orifice Plates in some G3520C Landfill Engines {1063, 1380}
C9.3 Tier 4 Interim Engines Fuel Pressure Is High
C9.3 Tier 4 Interim Engines Power Is Intermittently Low or Power Cutout Is Intermittent