Engine Oil Pan - Remove and Install
拆卸步骤
- 将发动机机油排入合适的容器以便保存或弃置。 有关正确的步骤,请参阅操作和保养手册。
- 拆下螺栓 (1) 和 (3) 。
Show/hide table
图 1 | g02141944 |
- 松开接头 (4) ,然后拆下机油表 (2) 。
- 拆下螺母 (5) 。 拆下开关组件 (6) 。 拆下噪声抑制盖 (7) 。
Show/hide table
图 2 | g02141932 |
- 拆下螺栓 (8) 。 拆下双头螺栓 (9) 。 拆下发动机油底壳 (10) 和密封垫。
Show/hide table
图 3 | g02141942 |
注: 不要撬动或凿打发动机油底壳的密封表面。 必要时,利用橡皮锤轻轻敲打发动机油底壳。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A.     | −     | Loctite 587     | −     |
- 应该将工具 (A) 涂抹到位置 (X) 并达到宽度为 4.00 ± 1.00 mm (0.158 ± 0.040 in)。 将工具 (A) 涂抹到接头处。
Show/hide table
图 4 | g02142246 |
- 将一个新密封垫和发动机油底壳 (10) 放置到缸体上。
Show/hide table
图 5 | g02141942 |
Show/hide table
图 6 | g02142370 |
- 安装双头螺栓 (8) 。 安装螺栓 (9) 。 安装螺栓 (9) 。
- 拧紧双头螺栓 (8) ,然后根据图 7 中所示的数字顺序拧紧螺栓 (9) 。
Show/hide table
图 7 | g02143244 |
发动机俯视图 发动机油底壳的拧紧顺序 |
- 安装噪声抑制盖 (7) 。 安装螺母 (5) 。 安装开关组件 (6) 。
Show/hide table
图 8 | g02141932 |
- 放置机油表 (2) ,然后拧紧接头 (4) 。
Show/hide table
图 9 | g02141944 |
- 安装螺栓 (1) 和 (3) 。
- 向发动机加注机油到正确的油位。 请参阅操作和维护手册, "发动机机油 - 更换"以了解正确的加注步骤。
Caterpillar Information System:
G3304B and G3306B Engines Engine Oil Filter Base - Remove
G3304B and G3306B Engines Engine Oil Cooler - Install
G3304B and G3306B Engines Engine Oil Cooler - Assemble
G3304B and G3306B Engines Engine Oil Cooler - Disassemble
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0702 - FMI 08
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0702 - FMI 04
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0702 - FMI 03
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0702 - FMI 02
2009/06/01 A New Software Is Available for Some On-Highway Engines {1901, 1902, 1920}
G3304B and G3306B Engines Engine Oil Cooler - Remove
2009/07/06 A New Liquid Detector Group Is Used for the Continuous Prelubrication System in 3600 and C280 Engines {1326, 1334, 1350}
Installation and Initial Start-Up Procedure for G3500B and G3500J Engines {1000} Installation and Initial Start-Up Procedure for G3500B and G3500J Engines {1000}
C15 and C18 Tier 4 Final Engines Lubrication System
G3304B and G3306B Engines Engine Oil Filter Base - Disassemble
2009/10/01 A New Gasket and Hardware Are Used for the Water Lines In Some 3500 and G3500 Engines {1052, 1380}
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0826 - FMI 03
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission MID 027 - CID 0826 - FMI 04
G3304B and G3306B Engines Engine Oil Filter Base - Assemble
G3304B and G3306B Engines Engine Oil Filter Base - Install
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes System Pressure - Release
G3304B and G3306B Engines Engine Monitoring System
G3304B and G3306B Engines Engine Oil Pan - Remove
G3304B and G3306B Engines Engine Oil Pan - Install
G3304B and G3306B Engines Boost Control Valve - Remove