Engine Speed/Timing Sensor - Clean/Inspect
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
Show/hide table
图 1 | g01368433 |
(1) 螺栓
(2) 传感器 (3) 线束组件 |
- 断开线束组件。
- 拆卸螺栓和传感器。
- 拆卸传感器的O 形密封圈。
检查传感器塑料端的磨损和脏污状况。 清理传感器表面的金属屑和其它碎屑。
- 将新的 O 形密封圈装在传感器上。 用清洁的发动机机油润滑 O 形密封圈。
- 将传感器在壳体上定位并安装螺栓。
- 连接线束组件。
Show/hide table
图 2 | g01900805 |
(4) 螺栓
(5) 传感器 (6) 线束 |
- 断开线束组件。
- 拆卸螺栓和传感器。
- 拆卸传感器的O 形密封圈。
检查传感器塑料端的磨损和脏污状况。 清理传感器表面的金属屑和其它碎屑。
- 将新的 O 形密封圈装在传感器上。 用清洁的发动机机油润滑 O 形密封圈。
- 在前壳体上安装位置传感器及螺栓。
- 连接线束组件。
Caterpillar Information System:
C32 Marine Engine Pinion Clearance - Adjust
C7.1 Industrial Engine and Generator Set Ignition Keyswitch Circuit and Battery Supply Circuit - Test
C7.1 Industrial Engine and Generator Set Engine Pressure Sensor Open or Short Circuit - Test
C15 and C18 Industrial Engines Clean Emissions Module Wiring - Remove and Install
C13 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install - Differential Pressure, Clean Emissions Module
C18 Marine Generator Set Product Description
C18 Marine Auxiliary Engine Product Description
C15 and C18 Industrial Engines Nozzle Heater Harness - Remove and Install
C13 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install - Clean Emissions Module
G3304B and G3306B Engines Diagnostic Trouble Codes
G3304B and G3306B Engines Fuel Shutoff - Test
793F and 797F Off-Highway Trucks Braking System Brakes Overheat
C13 Engines for Caterpillar Built Machines Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
C13, C15, and C18 Tier 4 Final Engines Boost Pressure Sensor
C27 and C32 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor
C13 Engines for Caterpillar Built Machines Soot Antenna - Remove and Install
C13 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install - Clean Emissions Module
C7.1 Industrial Engine and Generator Set Idle Validation Switch Circuit - Test
C13 Engines for Caterpillar Built Machines Catalyst - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
C7.1 Industrial Engine and Generator Set Indicator Lamp Circuit - Test
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
C9.3 Industrial Engine Air Compressor
Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125} Oversized Injector Sleeves for Remanufactured Cylinder Heads On Medium Sized Engines{1100, 1101, 1125}
793F and 797F Off-Highway Trucks Power Train Electronic Control System Retarder Is Aggressive