Engine Oil Filter Base - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 185-3630     | 带式扳手组件     | 1     |
开始:
- 拆下发动机机油冷却器。
- 断开管组件 (3) 。
Show/hide table
图 1 | g02157867 |
- 断开管组件 (2) 。
- 拆下四颗螺栓 (1) 。
- 拆下螺栓 (4) 后拆下油滤清器底座 (5) 。
- 拆下四条螺栓 (7) 后将歧管 (6) 从歧管 (8) 上分离。
Show/hide table
图 2 | g02157868 |
- (拆下螺塞) 11。 拆下弹簧 (10) 和柱塞 (9) 。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 断开管组件 (12) 。
Show/hide table
图 3 | g02157869 |
注: 将滤清器壳体中的油排入适当的容器中,以便保存或处理。
- 拆下螺栓 (13) 后拆下机油滤清器底座 (14) 。
- 利用工具 (A) 拆下滤清器 (19) 。
Show/hide table
图 4 | g02157977 |
- 拆下螺塞 (18) 、O 形圈 (17) 、弹簧 (16) 和柱塞 (15) 。
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
安装步骤
- 按相反顺序安装机油滤清器底座。
- 拧紧螺塞 (18) 至扭矩为 100 ± 15 N·m (74 ± 11 lb ft)。
- 利用工具 (A) 安装滤清器 (19) 。 将滤清器 (19) 上紧到 100 ± 15 N·m (74 ± 11 lb ft) 的扭矩。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
Caterpillar Information System:
Procedure to Convert the Oil Supply Line to the Variable Valve Actuators (VVA) on C15 On-Highway Engines{1105, 1130, 1307} Procedure to Convert the Oil Supply Line to the Variable Valve Actuators (VVA) on C15 On-Highway Engines{1105, 1130, 1307}
G3500B Engines Exhaust Manifold
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D and 793F Off-Highway Truck Automatic Lubrication System Lubrication Injectors - Adjust
2009/04/06 Special Instruction, REHS3411, "Procedure for the Installation of the 304-4209 Nitrogen Oxide Sensor Gp " Is Available {191N}
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Assemble
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Disassemble
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Install
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Remove
Determining the Cause of Fuel Dilution of Engine Oil for On-highway Engines{1250, 1348} Determining the Cause of Fuel Dilution of Engine Oil for On-highway Engines{1250, 1348}
CX31 On-Highway Transmission Power Train Retarder - Assemble
CX31 On-Highway Transmission Power Train Retarder - Disassemble
Measuring Fuel Dilution of On-highway Engines{1250, 1348} Measuring Fuel Dilution of On-highway Engines{1250, 1348}
C18 Generator Set Fuel System Primary Filter - Replace
G3500 A3 Engines Cover Group (Front Housing)
G3500B Engines Crankcase Breather
2009/03/16 A New Angle Sensor is Now Available for AccuGrade and CAES Systems on Excavators {1439, 5953}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0168 - FMI 04
Troubleshooting Guide for Leaks in the Vacuum of Certain UPS Systems{4287} Troubleshooting Guide for Leaks in the Vacuum of Certain UPS Systems{4287}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0248 - FMI 09
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
2009/03/30 A New Actuator Kit (Wastegate) and a New Turbocharger Are Available for Claas Engines {1052, 1053, 1057, 1940}
G3500B Engines Camshaft
CX31-P600 Petroleum Transmission Well Servicing Transmission Planetary - Disassemble
CX31-P600 Petroleum Transmission Well Servicing Transmission Planetary - Assemble