Retarder Hydraulic Control Valve - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 4C-9507     | 固定胶     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 安装 O 形密封圈 (22) 。
Show/hide table
图 1 | g01849561 |
- 安装阀芯 (21) 。 将工具 (A) 涂抹到节流孔 (20) 上。 安装节流孔 (20) 。 将节流孔 (20) 上紧到 2 + 0.5 - 0.0 N·m (18 + 4 - 0 lb in) 的扭矩。
Show/hide table
图 2 | g01849553 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装弹簧 (19) 。 滑阀组件 (18) 和螺塞组件 (17) 。 拧紧螺塞组件 (17) 至扭矩为 25 ± 5 N·m (18 ± 4 lb ft)。
- 安装 O 形密封圈 (16) 。
Show/hide table
图 3 | g01849536 |
- 安装板 (15) 和阀体 (14) 。 安装螺栓 (13) 。 将螺栓 (13) 拧紧至 30 ± 4 N·m (22± 3 lb ft) 的扭矩。
Show/hide table
图 4 | g01849395 |
- 安装 O 形密封圈 (12) 。
Show/hide table
图 5 | g01849353 |
- 安装螺母 (9) 和垫圈。 安装芯组件 (11) 。 拧紧芯组件 (11) 至扭矩为 50 ± 5 N·m (37 ± 4 lb ft)。 安装线圈组件 (10) 。 安装垫圈和螺母 (9) 。 将螺母 (9) 拧紧至 13 ± 1.5 N·m (115 ± 13.3 lb in) 的扭矩。
Show/hide table
图 6 | g01849014 |
- 安装弹簧 (8) 、止动块 (7) 、弹簧 (6) 和缓动阀 (5) 。
Show/hide table
图 7 | g01848954 |
Show/hide table
图 8 | g01846975 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装滑阀 (4) 。 安装 O 形密封圈 (3) 。
- 安装盖 (2) 和螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 30 ± 4 N·m (22 ± 3 lb ft)。
Show/hide table
图 9 | g01846963 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
End By: 安装减速器液压控制阀。 请参阅 拆解和装配, "减速器液压控制阀 - 安装"。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Disassemble
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Install
CX31-P600 Petroleum Transmission Well Servicing Retarder Hydraulic Control Valve - Remove
Determining the Cause of Fuel Dilution of Engine Oil for On-highway Engines{1250, 1348} Determining the Cause of Fuel Dilution of Engine Oil for On-highway Engines{1250, 1348}
CX31 On-Highway Transmission Power Train Retarder - Assemble
CX31 On-Highway Transmission Power Train Retarder - Disassemble
Measuring Fuel Dilution of On-highway Engines{1250, 1348} Measuring Fuel Dilution of On-highway Engines{1250, 1348}
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install
2013/01/28 Improved Hardware for the Camshaft Thrust Plate Is Used in Certain 3500 Engines {1204, 1210}
CX31 On-Highway Transmission Power Train Retarder - Install
CX31 On-Highway Transmission Power Train Retarder - Remove
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Disassemble
2009/04/06 Special Instruction, REHS3411, "Procedure for the Installation of the 304-4209 Nitrogen Oxide Sensor Gp " Is Available {191N}
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D and 793F Off-Highway Truck Automatic Lubrication System Lubrication Injectors - Adjust
G3500B Engines Exhaust Manifold
Procedure to Convert the Oil Supply Line to the Variable Valve Actuators (VVA) on C15 On-Highway Engines{1105, 1130, 1307} Procedure to Convert the Oil Supply Line to the Variable Valve Actuators (VVA) on C15 On-Highway Engines{1105, 1130, 1307}
C15 and C18 Industrial Engines Engine Oil Filter Base - Remove and Install
C18 Generator Set Fuel System Primary Filter - Replace
G3500 A3 Engines Cover Group (Front Housing)
G3500B Engines Crankcase Breather
2009/03/16 A New Angle Sensor is Now Available for AccuGrade and CAES Systems on Excavators {1439, 5953}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0168 - FMI 04
Troubleshooting Guide for Leaks in the Vacuum of Certain UPS Systems{4287} Troubleshooting Guide for Leaks in the Vacuum of Certain UPS Systems{4287}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0248 - FMI 09