Pump Drive - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 3     |
B     | 1P-2420     | 变速箱修复台     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 安装 O 形密封圈 (6) 。
Show/hide table
图 1 | g01805517 |
- 使用工具 (A) 和适当的起吊设备安装泵驱动装置 (5) 。 泵驱动装置 (5) 的重量约为 31 kg (70 lb)。 安装螺栓 (4) 。 将螺栓 (4) 拧紧至扭矩 100 ± 20 N·m (74 ± 15 lb ft)。
Show/hide table
图 2 | g01804753 |
- 安装护罩组件 (3) ,然后安装螺栓 (2) 。 将螺栓拧紧至 28 ± 7 N·m (21 ± 5 lb ft)。
Show/hide table
图 3 | g01804674 |
- 利用工具 (A) 和适当的起吊设备将变矩器壳体 (1) 从工具 (B) 上拆下。 变矩器 (1) 的重量约为 134 kg (295 lb)。
Show/hide table
图 4 | g01804644 |
End By:
- 安装变矩器。 请参阅 拆解和组装, "变矩器 - 安装"。
- 将变矩器安装到变速箱上。 请参阅 拆解和装配, "变速箱和变矩器 - 连接"。
Caterpillar Information System:
CX35-P800 Petroleum Transmission and Petroleum Power Train Packages Pump Drive - Remove
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0588 - FMI 09
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0588 - FMI 12
2009/02/16 Disposable Paper Air Filters Require Protection {1051, 1054}
795F AC and 795F AC XQ Off-Highway Trucks Air Filter Element (Inverter Cabinet) - Clean/Replace - Metal Sand Filters
2009/02/02 Shims Are Now Used in the Carburetors of G3516 Engines {1266}
3512B Generator Set Engine Diagnostic Trouble Codes
CX31-P600 Petroleum Transmission Well Servicing Relief Valve (Torque Converter Inlet) - Remove and Install
2009/02/02 A New Seal Is Used for the Ignition Transformers inG3600 Engines {1550, 7555}
2009/02/01 A New Connecting Rod Bearing is Available {1218, 1219, 1225}
2009/02/16 New Rocker Arms Are Available {1123}
C9 Marine Engines and C9 Marine Generator Sets Flexible Coupling
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0600 - FMI 04
2009/02/02 A New Rocker Arm Assembly is Available {1123}
2011/09/12 A New Rocker Arm Assembly Is Available {1123}
2009/03/02 Pressure Requirements for the Fuel Supply of the C175 Engine {1250}
2009/02/09 Improvement to the Oil Pressure Switch {7400, 7421}
2009/03/30 Introduction of a New Fuel Filter Base {1260, 1261}
CX35-P800 Petroleum Transmission and Petroleum Power Train Packages Pump Drive - Disassemble
CX35-P800 Petroleum Transmission and Petroleum Power Train Packages Pump Drive - Assemble
2009/04/06 New Software Is Available for C18 Marine Engines {1901, 1920}
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is Low - Fuel Transfer System
C175-16 and C175-20 Generator Set Engines Fuel Pressure Is High - Fuel Transfer System
345D, 349D and 349D2 Excavator Machine System Specifications Fan Drive Mounting Group