Use this procedure to troubleshoot the electrical system if a problem is suspected with the exhaust temperature sensors or if any one of the diagnostic codes in Table 1 is active or easily repeated.
| Diagnostic Codes Table | ||
|---|---|---|
| Code and Description | Conditions which Generate this Code | System Response |
| 827-8 Left Exhaust Temperature Sensor abnormal frequency, pulse width, or period | The Electronic Control Module (ECM) detects a sensor frequency that is greater than 1000 Hz or less than 150 Hz.
The ECM detects a duty cycle that is greater than 90 percent or a duty cycle that is less than 10 percent. |
The code is logged.
The ECM flags exhaust temperature as invalid data. The value of the parameter is set to a default value. |
| 828-8 Right Exhaust Temperature Sensor abnormal frequency, pulse width, or period | ||
System Operation
The PWM sensors provide a signal to the engine's ECM. The sensors receive a 8.0 ± 0.4 VDC regulated voltage from the ECM.
The sensor's wires are routed from the ECM to the sensor connectors. The following list gives the terminal locations for the sensor connector.
- Terminal A digital sensor supply
- Terminal B digital sensor return
- Terminal C sensor signal
The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.
| |
| Illustration 1 | g01442587 |
|
Typical schematic | |
| |
| Illustration 2 | g01213937 |
|
P1 ECM connector (P1-4) Digital sensor supply (P1-5) Digital sensor return (P1-11) Left exhaust temperature (P1-12) Right exhaust temperature | |
| |
| Illustration 3 | g01383859 |
|
P2 ECM connector (P2-54) Digital sensor return (P2-56) Digital sensor supply | |
| |
| Illustration 4 | g01094844 |
|
Sensor connector (Pin A) Sensor supply (Pin B) Sensor return (Pin C) Signal | |
| |
| Illustration 5 | g01234146 |
|
Location of ECM connectors | |
Test Step 1. Check for "Active" or "Logged" Diagnostic Codes
- Connect Caterpillar Electronic Technician (ET) to the service tool connector.
- Turn the main disconnect switch to the ON position.
- Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
- Determine if a -8 diagnostic code is active for one of the exhaust temperature sensors.
Note: A diagnostic code that is logged several times is an indication of an intermittent problem. Most intermittent problems are the result of a bad connection between a socket and a pin in a connector or a bad connection between a wire and a terminal.
Expected Result:
No diagnostic code is active for the exhaust temperature sensors.
Results:
- OK - No diagnostic codes are active.
Repair: If the problem is intermittent, refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct procedures for inspecting electrical connectors.
STOP
- Not OK - A -8 diagnostic code is active or the diagnostic code is logged several times. Proceed to Test Step 2.
Test Step 2. Check the Digital Sensor Supply Voltage at the Sensor Connector
- Turn the main disconnect switch to the OFF position.
- Disconnect the suspect sensor(s) at the sensor connector.
- Turn the main disconnect switch to the ON position.
- Measure the voltage on the ECM side of the sensor connector between pin A and pin B for the suspect sensor(s).
Expected Result:
The digital sensor supply voltage is 8.0 ± 0.4 VDC.
Results:
- OK - The supply voltage is 8.0 ± 0.4 VDC. Proceed to Test Step 4.
- Not OK - The supply voltage is not 8.0 ± 0.4 VDC. Proceed to Test Step 3.
Test Step 3. Check the Digital Sensor Supply Voltage at the ECM
- Turn the main disconnect switch to the OFF position.
- Remove the wire for the digital sensor supply from P1-4. Install a wire jumper into the socket for P1-4.
- Remove the wire for the digital sensor supply from P2-56. Install a wire jumper into the socket for P2-56.
- Turn the main disconnect switch to the ON position.
- Measure the voltage between the wire jumper in terminal P1-4 and engine ground.
- Measure the voltage between the wire jumper in terminal P2-56 and engine ground.
- Turn the main disconnect switch to the OFF position.
- Remove the wire jumper and reconnect all wires. Reconnect ECM connector J1/P1.
Expected Result:
The digital sensor supply voltage is 8.0 ± 0.4 VDC.
Results:
- OK - The supply voltage is 8.0 ± 0.4 VDC. The supply voltage at the ECM is correct. There is a problem in the wiring between the ECM and the sensor connector. Repair the connectors or wiring and/or replace the connectors or wiring.
Repair: Repair the connectors or wiring and/or replace the connectors or wiring.
STOP
- Not OK - The supply voltage is not 8.0 ± 0.4 VDC. The voltage at the ECM is not correct.
Repair: Replace the ECM. Refer to Troubleshooting, "ECM - Replace". Verify that the problem is resolved.
STOP
Test Step 4. Check the Digital Sensor's Signal Frequency and the Duty Cycle at the Sensor Connector
- Turn the main disconnect switch to the OFF position.
- Remove the suspect sensor's signal wire from pin C of the sensor connector.
- Reconnect the suspect sensor connector.
- Turn the main disconnect switch to the ON position.
- Measure the frequency and the duty cycle between the sensor's signal wire and pin B of the suspect digital sensor at the sensor connector.
- Turn the main disconnect switch to the OFF position.
- Replace the sensor's signal wire and reconnect the sensor.
Expected Result:
The duty cycle is between 10 to 90 percent. The frequency reading is approximately 500 Hz.
Results:
- OK - The frequency and the duty cycle are correct. Proceed to Test Step 5.
- Not OK - The frequency or the duty cycle is not correct.
Repair: Replace the sensor. Verify that no diagnostic codes are active for the suspect sensor before permanently installing the sensor.
STOP
Test Step 5. Check the Digital Sensor's Duty Cycle at the ECM
- Remove the suspect signal wire for the sensor from ECM connector P1. Refer to Illustration 1 for the terminal locations for the ECM connector.
- Turn the main disconnect switch to the ON position.
- Measure the duty cycle between the sensor's signal wire and the sensor's return wire.
Note: Set the multimeter to "VDC". Press the "Hz" button twice so that the % symbol is displayed.
- Turn the main disconnect switch to the OFF position. Reconnect all wires.
Expected Result:
The duty cycle is between 10 to 90 percent.
Results:
- OK - The duty cycle is correct.
Repair: Replace the ECM. Refer to the diagnostic procedure Troubleshooting, "ECM - Replace".
STOP
- Not OK - The duty cycle is not correct.
Repair: There is a problem in the wiring between the ECM and the connector for the sensor. Repair the connectors and/or wiring between the ECM and the connector for the sensor.
STOP