Housing (Front) - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 256-4871 | 油封防护垫 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
如果未安装前壳体,请不要转动曲轴。否则,可能会损坏发动机。 |
- 确保前壳体组件 (6) 和曲轴的鼻端干净、无损坏。 清理板 (5) 的配合面。
Show/hide table
图 2 g01357161 典型示例 - 将工具 (A) 安装到曲轴的鼻端。
- 将销 (2) 与机油泵盖 (10) 上的孔 (X) 对准。 确保机油泵盖与惰轮组件 (11) 同心。
- 将新的接头安装到板 (5) 上。
- 将喷油泵的连杆引入位,以使连杆在缸体的孔内活动自如。 对准前壳体 (6) 和板 (5) 上的定位销。 将前壳体 (6) 安装到板 (5) 上。
- 安装紧固件 (3) 并紧固至扭矩
10 N·m (89 lb in) 。 - 将工具 (A) 从曲轴的鼻端拆下。
- 将新的 O 形密封圈 (7) 安装到前壳体 (6) 上。 将盖 (8) 放到前壳体 (6) 上,然后安装螺母 (4) 和螺栓 (9)。
- 拧紧螺母 (4) 至扭矩为
50 N·m (37 lb ft) 。 - 如果发动机配备涡轮增压器,将软管连接到接头 (1) 上。
Show/hide table
图 1 | g01357158 |
典型示例 |
结束:
- 安装曲轴皮带轮。 请参阅拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
- 安装燃油喷油泵。 请参阅拆解和组装, "燃油喷油泵 - 安装"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine
2008/05/12 Improved Engine Software is Available {1901, 1920}
3406E and C15 Marine Engines Auxiliary Water Pump
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electrical System
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install - Connecting rods in position
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install