Flywheel - Remove
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 138-7573 | 连杆支架 | 1 |
| B | - | 导向双头螺栓 (M10 x 1.25 mm x 80mm) |
2 |
开始:
- 拆下电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 三缸发动机和四缸发动机的飞轮不同。 所有型号的拆卸步骤相似。
Show/hide table
| |
| 图 1 | g01305297 |
|
典型示例 | |
- 将工具 (A) 和适当的起吊设备安装在飞轮 (2) 上。 飞轮的重量约为
42 kg (93 lb) 。 - 从飞轮上的 (X) 部位卸下两个螺栓 (1)。
- 将工具 (B) 安装到飞轮上的 (X) 部位。
- 拆下其余螺栓 (1) 和飞轮 (2)。
注: 在某些三缸发动机上，曲轴和飞轮之间有一个滚销。
- 检查齿圈 (3) 和飞轮 (2) 有无磨损或损坏。 如果齿圈或飞轮发生磨损或损坏，则应使用新零件更换。
Show/hide table
图 2 g00825639 典型示例 - 要从飞轮 (2) 上拆下齿圈 (3)，将飞轮置于合适的支架上。 使用锤子（未显示）和冲头 (4) 将齿圈从飞轮上拆下。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C4.4 Industrial Engine Maintenance Interval Schedule
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
3406E and C15 Marine Engines Auxiliary Water Pump
2008/05/12 Improved Engine Software is Available {1901, 1920}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electrical System