Crankshaft Pulley - Remove and Install
开始:
- 拆下 V 形皮带。 有关更多资料,请参阅拆解和组装, " V 形皮带 - 拆卸和安装"。
Show/hide table
所需工具 | |||
工具 | 零件号 | 说明 | 数量 |
A | 8S-2264 | 拉拔器总成 | 1 |
- | 螺栓 | 3 |
- 松开螺母 (3)。
注: 使螺母与曲轴上的螺纹完全接合。
Show/hide table图 2 g01305772 - 将工具 (A) 安装到曲轴皮带轮 (2) 上。 使用工具 (A) 将曲轴皮带轮 (2) 从曲轴 (4) 上拆下。 拆下工具 (A)。
- 拆下螺母 (3)。
- 从曲轴 (4) 上拆下皮带轮 (2)。
- 从曲轴 (4) 上拆下半圆键 (1)。
Show/hide table
图 1 | g01326646 |
典型示例 |
- 确保下列部件干净、无损坏:曲轴锥面、半圆键和曲轴皮带轮孔。 更换任何损坏的部件。 在组装之前,确保曲轴锥面和曲轴皮带轮孔清洁、干燥。
Show/hide table
图 3 g01326646 典型示例 - 将半圆键 (1) 安装到曲轴 (4) 上。
- 将曲轴皮带轮 (2) 安装到曲轴 (4) 上。
- 用清洁的发动机机油润滑螺母 (3),然后安装此螺母。 拧紧螺母至扭矩
304 N·m (224 lb ft) 。
结束:
- 将 V 形皮带安装到发动机上。 请参阅拆解和组装, " V 形皮带 - 拆卸和安装"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
3406E and C15 Marine Engines Auxiliary Water Pump
2008/05/12 Improved Engine Software is Available {1901, 1920}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Naturally Aspirated Engines
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electrical System
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Timing - Check