Engine Oil Line - Remove and Install
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
| 注意 |
|---|
|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 松开将机油管 (1) 上的夹子固定到喷油泵上的螺母 (2)。
- 拆下中空螺栓 (3)，然后从缸体上拆下垫圈 (4)。
Show/hide table
图 2 g01307372 典型示例 - 拆下中空螺栓 (5)，然后从缸盖上拆下垫圈 (6)。
- 从发动机上拆下机油管 (1)。
Show/hide table
| |
| 图 1 | g01304820 |
|
典型示例 | |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将机油管 (1) 放到发动机上。 确保机油管上的夹子位于螺母 (2) 下方。
- 将中空螺栓 (3) 和新的垫圈 (4) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸体上并用手拧紧。
Show/hide table
图 4 g01307372 典型示例 - 将中空螺栓 (5) 和新的垫圈 (6) 置于机油管 (1) 上。 将中空螺栓和机油管安装到缸盖上并用手拧紧。
- 将螺母 (2) 拧紧至扭矩
15 N·m (133 lb in) ，该螺母将机油管 (1) 上的夹子固定到喷油泵上。 - 拧紧中空螺栓 (3) 和 (5) 至扭矩为
12 N·m (106 lb in) 。
Show/hide table
|
| |
| 图 3 | g01304820 |
|
典型示例 | |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C4.4 Industrial Engine Maintenance Interval Schedule
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
14L Motor Grader Machine Systems Circle Drive - Install
312D2 and 313D2 Excavators Machine Systems Storage Box and Covers (Cab) - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
3406E and C15 Marine Engines Auxiliary Water Pump
2008/05/12 Improved Engine Software is Available {1901, 1920}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Install