Engine Oil Pump - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 301-0285 | 定位工具 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
如果未安装前壳体,请不要转动曲轴。否则,可能会损坏发动机。 |
- 将工具 (A) 的销安装到缸体上。
- 将惰轮轮毂 (1) 安装到工具 (A) 的导板上。 将工具 (A) 的导板和工具 (A) 的销对准。
- 用锤子敲击工具 (A) 的导板。 将惰轮轮毂 (1) 敲入缸体,直到导板接触到缸体前部。
- 拆下工具 (A)。
Show/hide table
图 2 g01320621 - 安装曲轴 (18)。 请参阅拆解和组装, "曲轴 - 安装"。
- 将新的接头 (15) 放置在缸体上。 将板 (14) 与缸体中的定位销对准,安装板。 安装螺栓 (17) 并紧固至扭矩
10 N·m (89 lb in) 。 - 安装凸轮轴 (18)。 请参阅拆解和组装, "凸轮轴 - 安装"。
Show/hide table
图 1 | g01305803 |
典型示例 |
- 安装止推垫圈 (2)。 用清洁的发动机机油润滑止推垫圈。
Show/hide table
图 4 g01305805 典型示例 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 在内转子 (4) 的表面和惰轮齿轮 (3) 的叶片上涂敷清洁的发动机机油。
- 对正惰轮齿轮 (3) 上的正时标记 (X) 与齿轮 (19) 和 (20) 上的相应正时标记。 将惰轮齿轮 (3) 安装到惰轮轮毂 (1) 上。
- 将内转子 (4) 安装到惰轮齿轮 (3) 上。
Show/hide table
突然释放弹簧作用力可能会导致人身伤害。
驱动轴、活塞和传动齿轮都受到弹簧力的作用。
在拆卸部件前,使用压具慢慢释放弹簧作用力。
- 将以下部件安装到惰轮轮毂 (1) 上:
- 机油泵盖 (5)
- 垫片 (6)
- 弹簧 (7)
- 套圈 (8)
参考图 3。
- 将挡圈 (9) 安装到惰轮轮毂 (1) 上。
Show/hide table
图 5 g01320625 用塞尺检查端隙。 - 用塞尺测量发动机机油泵的端隙。 请参阅技术规格, "发动机机油泵"。
- 如果已拆下机油滤网,遵循步骤 8.a 至 8.c 来安装机油滤网。
- 将新的 O 形密封圈 (10) 安装到机油管组件 (11) 上。
- 将吸油管 (11) 安装到缸体上。
- 将机油滤网 (13) 安装到缸体上并将螺栓 (12) 拧紧至扭矩
11 N·m (97 lb in) 。
Show/hide table图 6 g01327023
Show/hide table
图 3 | g01304840 |
典型示例 |
结束:
- 安装前壳体。 请参阅拆解和组装, "壳体(前) - 安装"。
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Line - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injector - Remove and Install
C4.4 Industrial Engine Refill Capacities and Recommendations
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3176C, 3406E and 3456 Industrial Engines Sensor Signal (Analog, Active) - Test
C4.4 Industrial Engine Maintenance Interval Schedule
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
14L Motor Grader Machine Systems Circle Drive - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
785D OEM Off-Highway Truck Suspension Cylinder Pressure Sensor (Front Suspension Cylinder)
3406E and C15 Marine Engines Auxiliary Water Pump
2008/05/12 Improved Engine Software is Available {1901, 1920}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Basic Engine
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines General Information
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install - Naturally Aspirated Engines