Engine Oil Filter Housing - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 439-3938 | Link Bracket | 3 |
Start By:
- Remove the temperature control valve.
- Drain the oil from the engine oil filter housing into a suitable container for storage or for disposal.
Show/hide table
Illustration 1 g06094597 - Remove bolts (1), bolts (4), nuts (2), elbow (3), and the O-ring seals.
Show/hide table
Illustration 2 g06094608 - Remove bolts (5), stud (6), stud (7), and use two people to remove housing (8) and tubes (9). The approximate weight of housing (8)
25 kg (55 lb) .Show/hide tableIllustration 3 g06094687 - Attach Tooling (A) and a suitable lifting device to engine oil filter housing (10). The approximate weight of engine oil filter housing (10)
186 kg (410 lb) . - Remove bolts (11), bolts (13), and disconnect tubes (13).
Show/hide table
Illustration 4 g06094717 - Remove bolts (15) and engine oil filter housing (10).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Caterpillar Information System:
Axle Pinion Seal Leaks on Certain Wheel Loaders {3260, 3278} Axle Pinion Seal Leaks on Certain Wheel Loaders {3260, 3278}
New Front Axle and Rear Axle Groups Are Now Used on Certain Compact Wheel Loaders and Integrated Toolcarriers {3278} New Front Axle and Rear Axle Groups Are Now Used on Certain Compact Wheel Loaders and Integrated Toolcarriers {3278}
A New First and Third Shaft in the Transmission is Now Available on all C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170} A New First and Third Shaft in the Transmission is Now Available on all C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170}
Transmission Assembly Instructions for the First and Third Shaft in the Transmission on Certain C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170} Transmission Assembly Instructions for the First and Third Shaft in the Transmission on Certain C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Component Location
C175-16 and C175-20 Locomotive Engines Pistons, Liners, and Connecting Rods - Remove
Cat® Object Detection System MID 134 - CID 3323 - FMI 11
D5R and D6N Track-Type Tractor Machine Systems Ripper Lift Cylinder - Remove and Install
C13 Engines for Caterpillar Built Machines Retarder - Test
Cat® Object Detection System MID 134 - CID 3323 - FMI 09
Cat® Object Detection System MID 134 - CID 3322 - FMI 12
Cat® Object Detection System MID 134 - CID 3322 - FMI 11
Cat® Object Detection System MID 134 - CID 3323 - FMI 12
New Implement Software Is Now Used on Certain 988K Large Wheel Loaders {7610, 7620} New Implement Software Is Now Used on Certain 988K Large Wheel Loaders {7610, 7620}
Cat® Product Link Firmware is Now Available for Certain K Series Wheel Loaders {7606} Cat® Product Link Firmware is Now Available for Certain K Series Wheel Loaders {7606}
C13 Engines for Caterpillar Built Machines Fuel Pressure Is High
340F Excavator Stopping the Engine
988K XE Wheel Loader Fuses and Circuit Breakers - Replace/Reset
Cat® Object Detection System MID 134 - CID 3329 - FMI 03
Cat® Object Detection System MID 134 - CID 3329 - FMI 04
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Approved Machines
TRS10, TRS14, TRS18, and TRS23 Tilt-Rotator Lifting and Tying Down
Cat® Object Detection System MID 134 - CID 3330 - FMI 03
Cat® Object Detection System MID 134 - CID 3330 - FMI 04