Ripper Lift Cylinder - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | 1/2-13 by 3 inch Forcing Bolt | 2 |
Start By:
- Release the hydraulic system pressure.
Show/hide table
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Remove bolts (1) and (2). Disconnect hose assemblies (3).
Show/hide table
Illustration 2 g06094465 - Remove bolts (4) and retainer (5). Remove pin (4).
Show/hide table
Illustration 3 g06094479 - Attach a suitable lifting device to ripper lift cylinder (7).
Show/hide table
Illustration 4 g06094487 - Remove bolts (8) from bearing (9). Complete for both side of ripper lift cylinder (7).
Show/hide table
Illustration 5 g06094546 - Use Tooling (A) to remove bearing (9). Remove ripper lift cylinder (7). The weight of ripper lift cylinder (7) is approximately
100 kg (220 lb) .
Show/hide table
Illustration 1 | g06094446 |
- Install ripper lift cylinder (7) in the reverse order of removal.
Disassembly and Assembly Information
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Retaining Compound 620 | - |
B | - | Loctite 242 | - |
C | 127-4904 | Hydraulic Cylinder Repair Stand Gp | 1 |
D | 1P-0510 | Driver Gp | 1 |
E | 231-4349 | Bearing Puller Adapter | 1 |
4C-9633 | Puller Stud | 1 | |
9U-6832 | Nut | 1 | |
6V-3160 | Double Acting Cylinder | 1 | |
350-7768 | Electric Hydraulic Pump Gp (115V) | 1 | |
350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
9S-5565 | Pin Puller Sleeve As | 1 |
- Lubricate threads and tighten locknut (15) to a torque of
2700 ± 270 N·m (1991 ± 199 lb ft) . - Lubricate threads and tighten bolts (14) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .
Show/hide table
Illustration 6 | g06094747 |
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Retarder - Test
Cat® Object Detection System MID 134 - CID 3323 - FMI 09
Cat® Object Detection System MID 134 - CID 3322 - FMI 12
Cat® Object Detection System MID 134 - CID 3322 - FMI 11
Cat® Object Detection System MID 134 - CID 3322 - FMI 09
Cat® Object Detection System MID 134 - CID 3319 - FMI 12
Cat® Object Detection System MID 134 - CID 3319 - FMI 11
Cat® Object Detection System MID 134 - CID 3319 - FMI 09
D11T Track-Type Tractors Repair Procedure for the Suction Tube for the Following 433-9240 Fuel Tank Gp, 372-3001 Fuel Tank Gp, 433-5916 Fuel Tank Gp, 335-5343 Fuel Tank Gp, 431-6687 Fue D11T Track-Type Tractors Repair Procedure for the Suction Tube for the Following 433-9240 Fuel Tank Gp, 372-3001 Fuel Tank Gp, 433-5916 Fuel Tank Gp, 335-5343 Fuel Tank Gp, 431-6687 Fue
Cat® Object Detection System MID 134 - CID 3318 - FMI 12
Cat® Object Detection System MID 134 - CID 3318 - FMI 11
Cat® Object Detection System MID 134 - CID 3318 - FMI 09
Cat® Object Detection System MID 134 - CID 3323 - FMI 11
C175-16 and C175-20 Locomotive Engines Pistons, Liners, and Connecting Rods - Remove
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Component Location
Transmission Assembly Instructions for the First and Third Shaft in the Transmission on Certain C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170} Transmission Assembly Instructions for the First and Third Shaft in the Transmission on Certain C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170}
A New First and Third Shaft in the Transmission is Now Available on all C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170} A New First and Third Shaft in the Transmission is Now Available on all C Series Wheel Skidders and 938H Wheel Loaders {0374, 0700, 3030, 3063, 3155, 3169, 3170}
New Front Axle and Rear Axle Groups Are Now Used on Certain Compact Wheel Loaders and Integrated Toolcarriers {3278} New Front Axle and Rear Axle Groups Are Now Used on Certain Compact Wheel Loaders and Integrated Toolcarriers {3278}
Axle Pinion Seal Leaks on Certain Wheel Loaders {3260, 3278} Axle Pinion Seal Leaks on Certain Wheel Loaders {3260, 3278}
C175-16 and C175-20 Locomotive Engines Engine Oil Filter Housing - Remove
Cat® Object Detection System MID 134 - CID 3323 - FMI 12
New Implement Software Is Now Used on Certain 988K Large Wheel Loaders {7610, 7620} New Implement Software Is Now Used on Certain 988K Large Wheel Loaders {7610, 7620}
Cat® Product Link Firmware is Now Available for Certain K Series Wheel Loaders {7606} Cat® Product Link Firmware is Now Available for Certain K Series Wheel Loaders {7606}
C13 Engines for Caterpillar Built Machines Fuel Pressure Is High