Crankshaft Position for Valve Lash Setting
The SAE standard engine crankshaft rotation is counterclockwise when the crankshaft is viewed from the flywheel end.
Show/hide table
| Crankshaft Positions for Valve Lash Setting
Standard Counterclockwise Rotation |
|||
| Engine | Stroke for the Number 1 Piston At the Top Center Position (1) | Inlet Valves | Exhaust Valves |
| G3516 | Compression Stroke | 1-2-5-7-8-12-13-14 | 1-2-3-4-5-6-8-9 |
| Exhaust Stroke | 3-4-6-9-10-11-15-16 | 7-10-11-12-13-14-15-16 | |
| Firing Order | 1-2-5-6-3-4-9-10-15-16-11-12-13-14-7-8 | ||
Show/hide table
| (1) | Put the No. 1 Piston at the top center (TC) position and identify the correct stroke. Refer to Testing And Adjusting, "Finding the Top Center Position for the No. 1 Piston". Find the top center (TC) position for a particular stroke and make the adjustment for the correct cylinders. Remove the timing bolt. Turn the flywheel by 360 degrees in the direction of normal engine rotation. This will put the No. 1 piston at the top center (TC) position on the opposite stroke. Install the timing bolt in the flywheel and complete the adjustments for the cylinders that remain. |
Caterpillar Information System:
G3512 Generator Set Engines Camshaft
G3512 Generator Set Engines Crankshaft
G3500C and G3500E Generator Set Engines Aftercooler
G3500C and G3500E Generator Set Engines Ignition System
G3500C and G3500E Generator Set Engines Engine Sensors
G3500C and G3500E Generator Set Engines Electronic Control Module (ECM)
G3500C and G3500E Generator Set Engines Electronic Control System Operation
CX28 On-Highway Transmission Control Valve (Transmission Clutch Latching) - Install
G3500 A3 Engines Exhaust Bypass Valve - Adjust
2007/08/27 The Turbocharger Water Lines are Improved {1380}
CX28 On-Highway Transmission Control Valve (Transmission Clutch Latching) - Assemble
C7 Marine Engine Coolant Temperature Sensor
Bench Test Procedure for a 14L, 120M, 120M Series 2, 12M, 12M Series 2, 12M Series 3, 140M, 140M Series 2, 140M Series 3, 160M, 160M Series 2, and 160M Series 3 Motor Grader Transmission {3030, 3073} Bench Test Procedure for a 14L, 120M, 120M Series 2, 12M, 12M Series 2, 12M Series 3, 140M, 140M Series 2, 140M Series 3, 160M, 160M Series 2, and 160M Series 3 Motor Grader Transmission {3030, 3073}
G3520C and G3520E Engines Temperature Sensor
3408C and 3412C Marine Engines Fuel Injection Lines
3408B and 3408C Industrial and Marine Engines Camshaft Bearings
Procedure for the Installation of the 304-4209 Nitrogen Oxide Sensor Gp {191N} Procedure for the Installation of the 304-4209 Nitrogen Oxide Sensor Gp {191N}
C32 Marine Auxiliary Engines Configuration Parameters
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold
14L Motor Grader Transmission - Assemble
G3500C and G3500E Generator Set Engines Integrated Temperature Sensing Module
C7 Marine Engine Alternator and Regulator
2007/08/01 Retirement of the Paper Version of Truck Engine News {1000}
C7 Marine Engine Alternator and Regulator