Engine Oil Cooler - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that adapter (3) of the engine oil cooler is clean and free from damage. Clean the mating surfaces of the cylinder block.
- Position a new joint (5) (not shown) onto adapter (3). Install bolts (4) to the adapter.
- Install adapter (3) to the cylinder block. Tighten bolts (4) finger tight.
Note: The bolts are different lengths. Ensure that the different bolts are installed in the correct location. Ensure that any brackets that are secured by the bolts are installed in the correct location.
Show/hide tableIllustration 3 g01380915 Tightening sequence for the engine oil cooler - Tighten bolts (4) to a torque of
22 N·m (16 lb ft) . Tighten the bolts in the sequence that is shown in Illustration 3.Show/hide tableIllustration 4 g01380957 - Install a new sealing washer (6) to banjo bolt (1).
- Install new O-ring seal (7) and O-ring seal (8) to oil cooler body (2).
- Install banjo bolt (3) to oil cooler body (4).
Show/hide table
Illustration 5 g01444121 Typical example - Install the assembly of oil cooler body (2) to the adapter (3). Align the Connection (A) (not shown) with hose (9) and tighten hose clamps securely. Tighten the banjo bolt (1) to a torque of
57 N·m (42 lb ft) . - Connect the hose to Connections (B) to the assembly of oil cooler (2) and tighten hose clamp securely.
- Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
- Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter and Change" for the correct procedure.
- If necessary, Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Show/hide table
Illustration 1 | g01444650 |
Typical example |
Show/hide table
Illustration 2 | g01381216 |
Typical example |
Caterpillar Information System:
C3.3 Industrial Engine Engine Oil Cooler - Remove
C3.3 Industrial Engine Engine Oil Filter Base - Remove and Install
C3.3 Industrial Engine Inlet and Exhaust Valve Guides - Remove and Install
C3.3 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C3.3 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C3.3 Industrial Engine Exhaust Elbow - Remove and Install
C3.3 Industrial Engine Exhaust Manifold - Remove and Install
C3.3 Industrial Engine Turbocharger - Install
C3.3 Industrial Engine Fuel Injector Cover - Remove and Install
C3.3 Industrial Engine Turbocharger - Remove
C3.3 Industrial Engine Fuel Injector - Install
C3.3 Industrial Engine Fuel Injector - Remove
C3.3 Industrial Engine Engine Oil Relief Valve - Remove and Install
C3.3 Industrial Engine Engine Oil Pump - Remove and Install
C3.3 Industrial Engine Water Pump - Remove
C3.3 Industrial Engine Water Pump - Install
C3.3 Industrial Engine Water Temperature Regulator - Remove and Install
C3.3 Industrial Engine Flywheel - Remove
C3.3 Industrial Engine Flywheel - Install
C3.3 Industrial Engine Crankshaft Rear Seal - Remove
C3.3 Industrial Engine Crankshaft Rear Seal - Install
C3.3 Industrial Engine Flywheel Housing - Remove and Install
C3.3 Industrial Engine Crankshaft Pulley - Remove and Install
C3.3 Industrial Engine Crankshaft Wear Sleeve (Front) - Remove and Install