Stick - 2.9 m (9.51 ft)
Show/hide table
Illustration 1 | g03651409 |
Typical example |
Show/hide table
Specification for 441-0047 Hoe Stick Gp, 451-6217 Hoe Stick Gp, and 515-9773 Hoe Stick Gp | |||
Item | Qty | Part | Specification Description |
All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bushings , the bucket, and the cylinder pin bores. After you assemble the bushings, coat all the bores and the bushings with 5P-0960 Grease Cartridge. | |||
1 | 1 | 367-1461 Pin As | Diameter is |
2 | As required, use the following shims to adjust a maximum lateral clearance to |
||
1 | 151-0653 Shim | Thickness is |
|
2 | 093-0076 Shim | Thickness is |
|
1 | 093-0108 Shim | Thickness is |
|
3 | 1 | 367-1455 Pin As | Diameter is |
4 | 4 | 234-3748 Bushing(1) | Bore before assembly is |
Installation depth is |
|||
5 | 2 | - | Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. |
6 | 4 | 9X-4601 Lip Type Seal | Lubricate the sealing lip of the lip type seals lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install the lip type seals so that the lip type seals do not extend beyond the face of the boss. |
7 | As required, use the following shims to adjust a maximum lateral clearance to |
||
1 | 151-0653 Shim | Thickness is |
|
2 | 093-0076 Shim | Thickness is |
|
1 | 093-0108 Shim | Thickness is |
|
8 | 2 | 4I-4542 Bushing(1) | Bore before assembly is |
Installation depth is |
Show/hide table
(1) | Install the bushing in the bore so that the part number of the bushing is facing outward. |
Caterpillar Information System:
390F Excavator Machine System Stick - 4.4 m (14.44 ft)
2014/07/07 New Fan Hose Clamp Support Bracket Now Used on AD55B and AD60 Underground Articulated Trucks {5057}
Check the Gear Pump (Hoist, Steering, Brake, and Pilot) on AD30 Underground Articulated Trucks{4268, 4306, 5073, 5083, 5085} Check the Gear Pump (Hoist, Steering, Brake, and Pilot) on AD30 Underground Articulated Trucks{4268, 4306, 5073, 5083, 5085}
D6N Track-Type Tractor Ripper Tip and Shank Protector - Inspect/Replace - If Equipped
953K and 963K Track-Type Loaders Hydrostatic Transmission and Hydraulic System Filters - Replace
953K and 963K Track-Type Loaders Hydraulic Tank Breather - Replace
953K and 963K Track-Type Loaders Hydraulic System Oil Level - Check
953K and 963K Track-Type Loaders Hydraulic System Oil - Change
844K Wheel Dozer Relay - Test
844K Wheel Dozer Operator Control Switch (Switch to Ground) - Test
844K Wheel Dozer Sensor Supply - Test
844K Wheel Dozer Wiring Harness (Short Circuit) - Test
390F Excavator Machine System Stick - 3.4 m (11.15 ft)
980M and 982M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Output Transfer Gears
980L Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Planetary
390F Excavator Machine System Bucket Cylinder
990K Wheel Loader Machine Systems Input Transfer Gears - Adjust
D6R2 Track-Type Tractor Fuel System - Prime
980L Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Transmission Planetary
926M, 930M and 938M Wheel Loaders Additional Messages
2014/04/18 New Hose Assembly for the Pilot Lines Group Is Now Used on Certain D6R Track-Type Tractors {5057}
990K Wheel Loader Machine Systems Output Transfer Gears - Adjust
990K Wheel Loader Machine Systems Differential Backlash and Bearings - Adjust
844K Wheel Dozer Sensor Signal (PWM) - Test