Fuel Filter Base - Remove and Install
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 185-3630 | 带式扳手组件 | 1 |
| B | - | LOCTITE 271 | - |
- 将燃油供应转到 OFF 位置，并将电源断路开关转到 OFF 位置。
Show/hide table
图 1 g02823877 - 断开线束 (1)。
- 断开软管组件 (2) 和接头。
Show/hide table
图 2 g02823977 - 使用工具 (A) 拆下燃油滤清器 (6)。
- 拆下温度传感器 (4) 和压力传感器 (3)。
- 拆下燃油滤清器底座 (5)。
Show/hide table
图 3 g02845480 - 拆下适配器组件 (7) 和螺柱 (8)。
- 按与拆卸相反的顺序安装燃油滤清器底座 (5)。
- 将工具 (B) 涂抹到双头螺栓 (8) 的螺纹上。 工具 (B) 应覆盖双头螺栓的螺纹，如图所示达到距离 (C)，这是一个
7.6 ± 0.8 mm (0.3 ± 0.03 in) 的测量值。 - 将双头螺栓 (8) 拧紧至至扭矩为
70 ± 15 N·m (52 ± 11 lb ft) 。 - 将温度传感器 (4) 拧紧至扭矩为
20 ± 3 N·m (177 ± 27 lb in) 。 - 将压力传感器 (3) 拧紧至扭矩为
10 ± 2 N·m (89 ± 18 lb in) 。 - 在安装之前，用油液润滑即将密封的燃油滤清器密封件。 使用 (A) 将燃油滤清器 (5) 拧紧至扭矩为
35 ± 3 N·m (26 ± 2 lb ft) 。
Show/hide table
图 4 g02845499 - 将工具 (B) 涂抹到双头螺栓 (8) 的螺纹上。 工具 (B) 应覆盖双头螺栓的螺纹，如图所示达到距离 (C)，这是一个
Caterpillar Information System:
Product Identification Numbers (PIN) Location Guide Forest Machine
3500B Engines for Caterpillar Built Power Modules Cylinder Head
3500B and 3500C Marine Engines Fuel Injector
Bronze 379-8856 Engine Overhaul Kits for 3406 Machine Engines{1000} Bronze 379-8856 Engine Overhaul Kits for 3406 Machine Engines{1000}
D6N Track-Type Tractor Engine Supplement Temperature Sensor (DPF) - Remove and Install
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Disassemble - C3.3B Tier 4 Interim/Stage 3A
924K, 930K and 938K Wheel Loaders C6.6 Engine Supplement Diesel Particulate Filter
924K, 930K and 938K Wheel Loaders C6.6 Engine Supplement Belt Tensioner
D6N Track-Type Tractor Engine Supplement Soot Sensor - Remove and Install
826K Landfill Compactor Cooling System Water Temperature Regulator - Replace
Product Identification Numbers (PIN) Location Guide Load, Haul, Dump
D6N Track-Type Tractor Engine Supplement Secondary Fuel Filter and Base - Remove and Install
2012/01/20 The Track Shoes for D7G and D7H Track-Type Tractors Have Been Updated to Classic Track Shoe Part Numbers {4170}
C15 and C18 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Product Identification Numbers (PIN) Location Guide Cold Planer
C15 and C18 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Assemble - C3.3B Tier 4 Interim/Stage 3A
Product Identification Numbers (PIN) Location Guide Reclaimer Mixer
Product Identification Numbers (PIN) Location Guide Compactor (Soil)
924K, 930K and 938K Wheel Loaders Oil Pan
988K XE Wheel Loader Crankshaft Vibration Damper - Inspect
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Remove and Install - C3.3B Tier 4 Interim/Stage 3A
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
2012/02/17 Chassis Harness Improvements Are Now Used On 973D Track-Type Loaders With The Steel Mill Configuration {1408}