Cylinder Head
Show/hide table
| |
| 图 1 | g02823736 |
Show/hide table
| 技术规格 - 285-3086 缸盖总成和 101-0830 缸盖总成 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 2 | 130-2607 气门座镶圈 | 安装过程中，通过降低温度（参考温度： |
| 2 | 2 | 130-2608 气门座镶圈 | 安装过程中，通过降低温度（参考温度： |
| 3 | 5 | 3B-0623 杯塞 | 安装前，将 Loctite 11358 涂覆到杯塞的孔中。 |
| 4 | 5 | 3B-0645 杯塞 | 安装前，将 Loctite 11358 涂覆到杯塞的孔中。 |
| D | - | - | 杯塞的安装深度为 |
| E | - | - | 杯塞的安装深度为 |
Show/hide table
| |
| 图 2 | g02823737 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 5 | 1 | 5B-7890 管道螺塞 | 组装前，使用 Loctite C5A 铜防咬合剂润滑螺纹。 |
| 6 | 6 | 131-0420 缸盖紧固件总成. | 按照下列步骤拧紧缸盖的螺栓：
1. 组装前，将清洁的发动机机油涂抹到螺栓的螺纹上。 2. 按图 2 中所示的数字顺序将螺栓 1 至螺栓 8 拧紧至扭矩 3. 按图 2 中所示的数字顺序将螺栓 1 至螺栓 8 再次拧紧至扭矩 4. 按图 2 中所示的数字顺序将螺栓 1 至螺栓 8 再次拧紧至扭矩 5. 将螺栓 1 至螺栓 8 按数字顺序转到 180 ± 5 度，如图 2 所示。 6. 只有在螺栓 1 至螺栓 8 达到最终扭矩后，才拧紧两只螺栓 (8)。 7. 将两个螺栓 (8) 拧紧至 |
| 7 | 2 | 131-0421 缸盖紧固件总成. | |
| 8 | 2 | 5B-0213 螺栓 |
Caterpillar Information System:
3500B and 3500C Marine Engines Fuel Injector
Bronze 379-8856 Engine Overhaul Kits for 3406 Machine Engines{1000} Bronze 379-8856 Engine Overhaul Kits for 3406 Machine Engines{1000}
D6N Track-Type Tractor Engine Supplement Temperature Sensor (DPF) - Remove and Install
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Disassemble - C3.3B Tier 4 Interim/Stage 3A
924K, 930K and 938K Wheel Loaders C6.6 Engine Supplement Diesel Particulate Filter
924K, 930K and 938K Wheel Loaders C6.6 Engine Supplement Belt Tensioner
D6N Track-Type Tractor Engine Supplement Soot Sensor - Remove and Install
826K Landfill Compactor Cooling System Water Temperature Regulator - Replace
Product Identification Numbers (PIN) Location Guide Load, Haul, Dump
D6N Track-Type Tractor Engine Supplement Secondary Fuel Filter and Base - Remove and Install
924K, 930K and 938K Wheel Loaders Air Cleaner
D6N Track-Type Tractor Engine Supplement Primary Fuel Filter, Water Separator and Base - Remove and Install
Product Identification Numbers (PIN) Location Guide Forest Machine
C15 and C18 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
2012/01/20 The Track Shoes for D7G and D7H Track-Type Tractors Have Been Updated to Classic Track Shoe Part Numbers {4170}
C15 and C18 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Product Identification Numbers (PIN) Location Guide Cold Planer
C15 and C18 Engines for Caterpillar Built Machines Fuel Manifold (ARD) - Remove and Install
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Assemble - C3.3B Tier 4 Interim/Stage 3A
Product Identification Numbers (PIN) Location Guide Reclaimer Mixer
Product Identification Numbers (PIN) Location Guide Compactor (Soil)
924K, 930K and 938K Wheel Loaders Oil Pan
988K XE Wheel Loader Crankshaft Vibration Damper - Inspect
C2.6 and C3.3B Engines for Caterpillar Built Machines Exhaust Gas Recirculation Valve - Remove and Install - C3.3B Tier 4 Interim/Stage 3A