Crankshaft Main Bearings - Remove
开始:
- 拆下曲轴组件。 请参阅拆解和组装, "曲轴 - 拆卸"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保标记轴承盖的方位和正确位置。
Show/hide table
图 1 g01327056 Show/hide table
图 2 g01327033 典型示例 - 将螺栓 (1) 和上主轴承盖 (2) 从下主轴承盖 (6) 上拆下。
- 对于 C1.5 发动机，拆下止推垫圈 (7)。
对于 C2.2 发动机，拆下止推垫圈 (3) 和 (7)。
- 将主轴承 (4) 和 (5) 从主轴承盖上拆下。 将主轴承与相应的轴承盖保存在一起。
- 切勿从主轴承盖上拆下定位销 (8)。
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0510 | 冲头总成 | 1 |
- 使用工具 (A) 将曲轴轴承 (9) 从缸体上拆下。
Show/hide table
| |
| 图 3 | g01327066 |
Caterpillar Information System:
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C15 On-Highway Engine Exhaust Manifold
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
G3520C and G3520E Generator Set Engines Ignition Secondary - Test
G3520C and G3520E Generator Set Engines Ignition Primary - Test
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install