Engine Oil Cooler - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 185-3630 | 皮带式扳手 | 1 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从冷却系统将冷却液排入合适的容器中。 有关正确的程序,请参阅操作和保养手册, "冷却系统冷却液 - 排放"。
- 将发动机机油排入合适的容器中。 有关正确的步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
Show/hide table
图 1 g01304837 典型示例 - 使用工具 (A) 拆下机油滤清器滤芯 (5)。
- 松开软管卡箍 (2) 后断开软管 (1)。 记录冷却液进口和冷却液出口的位置,以方便安装。
- 拆下接头 (4),然后将机油冷却器 (3) 从缸体上拆下。
注: 作临时标记以指示机油冷却器的方位,方便安装。
- 将 O 形密封圈 (6) 从机油冷却器 (3) 上拆下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保机油冷却器清洁、无损坏。 清洁缸体的配合面。
Show/hide table
图 2 g01304837 典型示例 - 将新的 O 形密封圈 (6) 安装到机油冷却器 (3) 上。 将机油冷却器 (3) 放到缸体上并安装接头 (4)。 拧紧适配器 (4) 至扭矩为
34 N·m (25 lb ft) 。注: 确保机油冷却器的方位正确。
- 将软管 (1) 连接到机油冷却器 (3) 上的冷却液进口和冷却液出口。 拧紧软管卡箍 (2)。
- 安装新的机油滤清器滤芯 (5)。
- 加注冷却系统至正确液位。 请参阅操作和保养手册, "冷却系统冷却液 - 加注"以了解正确程序。
- 加注发动机油底壳至正确油位。 有关正确的步骤,请参阅操作和保养手册, "发动机机油滤清器 - 更换"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C15 On-Highway Engine Exhaust Manifold
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove