Engine Support (Rear)
Show/hide table
| |
| Illustration 1 | g01302593 |
|
Top view | |
Show/hide table
| |
| Illustration 2 | g01302592 |
|
Rear view | |
Use the following procedure to tighten the studs and bolts:
- Tighten stud (9) through stud (12) in the numerical sequence that is shown in Illustration 2 to
5 ± 5 N·m (45 ± 45 lb in) . - Tighten bolt (1) through bolt (8) in the numerical sequence that is shown in Illustration 1 to
47 ± 9 N·m (35 ± 7 lb ft) . - Again, tighten stud (9) through stud (12) in the numerical sequence that is shown in Illustration 2 to
47 ± 9 N·m (35 ± 7 lb ft) .
Caterpillar Information System:
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C15 On-Highway Engine Exhaust Manifold
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
G3520C and G3520E Generator Set Engines Ignition Secondary - Test
G3520C and G3520E Generator Set Engines Ignition Primary - Test
2006/10/02 Use Only Cleaning Agents that are Water Based with the 212-1503 Parts Washer Kit {0680}
G3520C and G3520E Generator Set Engines Fuel Metering Valve - Test
C11 and C13 Petroleum Engines Air Lines
C13 On-highway Engine Air Lines
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install