Engine Oil Pump - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A(1) | 256-4862 | 定位工具 | 1 |
A(2) | 256-4864 | 定位工具 | 1 |
A(3) | 301-0285 | 定位工具 | 1 |
B | 1P-0808 | 多功能润滑脂 | 1 |
Show/hide table
(1) | C0.5 和 C0.7 发动机 |
(2) | C1.1 和 C1.6 发动机 |
(3) | C1.5 和 C2.2 发动机 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
如果未安装前壳体,请不要转动曲轴。否则,可能会损坏发动机。 |
- 将工具 (A) 的销子安装到缸体上。
- 将惰轮轮毂 (1) 安装到工具 (A) 的导板上。 将工具 (A) 的导板和工具 (A) 的销子对准。
- 用锤子敲击工具 (A) 的导板。 将惰轮轮毂 (1) 敲入缸体,直到导板接触到缸体前部。
- 拆下工具 (A)。
Show/hide table
图 2 g01320621 - 安装曲轴 (18)。 请参阅拆解和组装, "曲轴 - 安装"。
- 将新的接头 (15) 放置在缸体上。 将板 (14) 和缸体上的定位销对准,然后安装板。 安装螺栓 (17) 并紧固至扭矩
10 N·m (89 lb in) 。 - 安装凸轮轴 (18)。 请参阅拆解和组装, "凸轮轴 - 安装"。
Show/hide table
图 1 | g01305803 |
典型示例 |
- 安装止推垫圈 (2)。 用清洁的发动机机油润滑止推垫圈。
Show/hide table
图 4 g01305805 典型示例 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 在内转子 (4) 的表面和惰轮齿轮 (3) 的叶片上涂敷工具 (B)。
- 对正惰轮齿轮 (3) 上的正时标记 (X) 与齿轮 (19) 和 (20) 上的相应正时标记。 将惰轮齿轮 (3) 安装到惰轮轮毂 (1) 上。
- 将内转子 (4) 安装到惰轮齿轮 (3) 上。
Show/hide table
突然释放弹簧作用力可能会导致人身伤害。
驱动轴、活塞和传动齿轮都受到弹簧力的作用。
在拆卸部件前,使用压具慢慢释放弹簧作用力。
- 将以下部件安装到惰轮轮毂 (1) 上:
- 机油泵盖 (5)
- 垫片 (6)
- 弹簧 (7)
- 套圈 (8)
参考图 3。
- 将挡圈 (9) 安装到惰轮轮毂 (1) 上。
Show/hide table
图 5 g01320625 用塞尺检查端隙。 - 用塞尺测量发动机机油泵的端隙。 请参阅技术规格, "发动机机油泵"。
- 如果先前已拆下机油滤网,遵循步骤 8.a 至 8.c 来安装机油滤网。
- 将新的 O 形密封圈 (10) 安装到机油管组件 (11) 上。
- 将吸油管 (11) 安装到缸体上。
- 将机油滤网 (13) 安装到缸体上,并将螺栓 (12) 紧固至扭矩
11 N·m (97 lb in) 。
Show/hide table图 6 g01327023
Show/hide table
图 3 | g01304840 |
典型示例 |
结束:
- 安装前壳体。 请参阅拆解和组装, "壳体(前) - 安装"。
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Inlet and Exhaust Valves - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install