Engine Oil Pan - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 两缸、三缸和四缸发动机配备了不同的发动机油底壳。 所有机型的拆卸步骤相似。
- 从发动机油底壳 (2) 上拆下排放螺塞 (5)。 将发动机机油排入合适的容器以便保存或弃置。 请参阅操作和保养手册, "机油滤清器更换"以了解正确程序。
- 从排放螺塞 (5) 上拆下密封垫圈 (3)。
- 将螺栓 (4) 从发动机油底壳 (2) 上拆下。
- 从发动机上拆下发动机油底壳 (2)。
- 卸下接头 (1)。
Show/hide table
图 1 | g01326659 |
典型示例 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 两缸、三缸和四缸发动机配备了不同的发动机油底壳。 所有机型的安装步骤相似。
- 确保发动机油底壳清洁且无损坏。 清洁缸体配合面。
- 将新的接头 (1) 和发动机油底壳 (2) 安装到发动机上。
- 安装螺栓 (4) 并紧固至扭矩
11 N·m (97 lb in) 。 - 将排放螺塞 (5) 和密封垫圈 (3) 安装到油底壳 (2) 上。
对于 C0.5 和 C0.7 发动机,将排放螺塞紧固至扭矩
34 N·m (25 lb ft) 。对于 C1.1、 C1.5、 C1.6 和 C2.2 发动机,将排放螺塞紧固至扭矩
34 N·m (25 lb ft) 。 - 加注发动机油底壳至正确油位。 有关正确的步骤,请参阅操作和保养手册, "发动机机油滤清器更换"。
Show/hide table
图 2 | g01326659 |
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C27 and C32 Generator Set Engines Engine Support (Rear)
C15 On-Highway Engine Clean Gas Induction Valve Actuator
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
C15 On-Highway Engine Exhaust Manifold
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Engine Oil Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fan - Remove and Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Fuel Injection Lines - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Disassemble
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Housing (Front) - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Inlet and Exhaust Valve Springs - Remove and Install