Exhaust Manifold
Show/hide table
Illustration 1 | g01527134 |
Exhaust manifold |
Note: Apply clean engine oil to the female ends of the exhaust manifold (3) before assembly. Apply 2P-2333 High Temperature Sealer to the male ends of the exhaust manifolds (1) before assembly. Remove excess sealer from the assembled joint.
Show/hide table
Illustration 2 | g01527135 |
Section A-A |
Use the following procedure to tighten the hose clamps (2) :
- Tighten two hose clamps to 5 ± 1 N·m (45 ± 9 lb in).
- Again, tighten two hose clamps 10 ± 1 N·m (90 ± 9 lb in).
Note: Apply 5P-3931 Anti-Seize Compound to the threads of the taperlock studs.
(4) Torque for 16 taperlock studs ... 35 ± 5 N·m (26 ± 4 lb ft)
Show/hide table
Illustration 3 | g00566145 |
Tightening sequence |
(5) Tighten the 12 locknuts in the numerical sequence that is shown in Illustration 3 to 38 ± 5 N·m (28 ± 4 lb ft).
Caterpillar Information System:
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
G3520C and G3520E Generator Set Engines Ignition Secondary - Test
G3520C and G3520E Generator Set Engines Ignition Primary - Test
2006/10/02 Use Only Cleaning Agents that are Water Based with the 212-1503 Parts Washer Kit {0680}
G3520C and G3520E Generator Set Engines Fuel Metering Valve - Test
C11 and C13 Petroleum Engines Air Lines
C13 On-highway Engine Air Lines
G3520C and G3520E Generator Set Engines Fuel Control - Test
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Transfer Pump - Test
C13 On-highway Engine Air Lines
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290} Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
C11 and C13 Engines and 14M and 16M Motor Graders Fuel Filter Is Restricted
C15 On-Highway Engine Exhaust Manifold
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module - Test
ECM Communication and Flashing Issues{0709, 1901, 7620} ECM Communication and Flashing Issues{0709, 1901, 7620}
C15 On-Highway Engine Clean Gas Induction Valve Actuator
C27 and C32 Generator Set Engines Engine Support (Rear)
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Install
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Main Bearings - Remove
C0.5, C0.7, C1.1, C1.5, C1.6 and and C2.2 Industrial Engines Crankshaft Pulley - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install