Relief Valve (Torque Converter Inlet) - Assemble
组装步骤
Show/hide table
| 需要的工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件名称 | 数量 |
| A | - | 螺杆 3/8" - 16 NC × 6" |
2 |
| 8T-4896 | 硬垫圈 | 2 | |
| 9S-8752 | 全高螺母 | 2 | |
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上，从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏，则应使用新件进行更换。
- 将塞 (12) 、O 形密封圈、盖 (13) 和螺栓 (14) 安装到阀体 (4) 上。
Show/hide table
 | |
| 图 1 | g01288127 |
- 将挺升阀 (8) 、弹簧 (9) 、护圈 (10) 和挡圈 (11) 安装在滑阀组件 (5) 中。
Show/hide table
 | |
| 图 2 | g01288115 |
Show/hide table
 |
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 将滑阀组件 (5) 、隔套 (6) 和弹簧 (7) 安装到阀体 (4) 中。
Show/hide table
 | |
| 图 3 | g01288114 |
Show/hide table
 | |
| 图 4 | g01288113 |
Show/hide table
 | |
| 图 5 | g01288111 |
Show/hide table
|
弹簧压缩零件如果安装不当，会伤害人体。 为避免伤害，遵照出版的装配程序，并穿上保护装备。 |
- 使用工具 (A) ，将盖 (2) 和 O 形密封圈抵在阀体 (4) 上安装。
- 卸下一套工具 (A) ，安装螺栓 (1) 。
- 再卸下一套工具 (A) ，安装螺栓 (3) 。
End By: 安装变矩器进口安全阀。 请参阅 解体和组装, "变距器进口安全阀 - 安装"。
Caterpillar Information System:
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Lockup Clutch and Solenoid Valve (Torque Converter) - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Lockup Clutch and Solenoid Valve (Torque Converter) - Remove
Ampseal 16 Connector Peripheral Seal Servicing{7553} Ampseal 16 Connector Peripheral Seal Servicing{7553}
C15 On-Highway Engine Turbocharger - Install - Low Pressure
C15 On-Highway Engine Turbocharger - Remove - Low Pressure
3606 and 3608 Engines Air Inlet Shutoff - Remove and Install
3512C Engine for Caterpillar Built Machines Speed Control
3512C Engine for Caterpillar Built Machines Sensor Supply
3512C Engine for Caterpillar Built Machines Pulse Width Modulated Sensor
349F and 352F Excavators Machine System Specifications Auxiliary Hydraulic Lines - Stick
C15 On-Highway Engine Precooler - Remove
C15 On-Highway Engine Precooler - Install
3512C Engine for Caterpillar Built Machines Electrical Connectors and Functions
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Install
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
C15 On-Highway Engine Clean Gas Induction Valve - Remove
C15 On-Highway Engine Clean Gas Induction Valve - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Assemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Control Manifold - Remove