Air Inlet Shutoff - Remove and Install
- Pull the emergency knob on the air intake shutoff or press the emergency stop button in order to release the blade latch on the air inlet shutoff.
Show/hide table
Illustration 1 g01287971 - Remove hose assembly (2) from air inlet shutoff (3).
- Remove bolts (4), bolts (6), and elbow (5).
- Remove bolts (1). Remove air inlet shutoff (3). Check the gaskets and replace the gaskets, if necessary.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Personal injury or death can occur from not following the proper procedure or the recommended tooling. To prevent the possibility of injury or death, follow the established procedure using the recommended tooling. |
Show/hide table
Before you remove the air intake shutoff, pull the trip knob on the air intake shutoff or press the emergency stop button in order to release the blade latch. If the blade latch is released after the air intake shutoff is removed, serious personal injury can result. |
- Clean all mating surfaces and install the gaskets and air inlet shutoff (3). Install bolts (1).
- Install elbow (5), bolts (4), and bolts (6).
- Install hose assembly (2) on air inlet shutoff (3).
- Reset the air inlet shutoff to the "OPEN" position.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 2 | g01287971 |
Caterpillar Information System:
3512C Engine for Caterpillar Built Machines Speed Control
3512C Engine for Caterpillar Built Machines Sensor Supply
3512C Engine for Caterpillar Built Machines Pulse Width Modulated Sensor
3500 and 3500B Engines Maintenance Recommendations
3512C Engine for Caterpillar Built Machines Permanent Timing Calibration Sensor
3606 and 3608 Engines Aftercooler - Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Vacuum Pump
G3520C and G3520E Engines Fuel Lines
Procedure to Remove Large Wheel Bearing Cups {4001, 4008, 4051, 4215} Procedure to Remove Large Wheel Bearing Cups {4001, 4008, 4051, 4215}
C15 On-Highway Engine Fuel Priming Pump - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Interface PWA
3512C Engine for Caterpillar Built Machines Override Switch
C15 On-Highway Engine Turbocharger - Remove - Low Pressure
C15 On-Highway Engine Turbocharger - Install - Low Pressure
Ampseal 16 Connector Peripheral Seal Servicing{7553} Ampseal 16 Connector Peripheral Seal Servicing{7553}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Lockup Clutch and Solenoid Valve (Torque Converter) - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Lockup Clutch and Solenoid Valve (Torque Converter) - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Torque Converter Inlet) - Assemble
349F and 352F Excavators Machine System Specifications Auxiliary Hydraulic Lines - Stick
C15 On-Highway Engine Precooler - Remove
C15 On-Highway Engine Precooler - Install