Fuel Filter Base - Assemble
Assembly Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Exceeding the listed torque specifications may cause low engine performance.
- Install O-ring seals (21) onto check valve assembly (12) .
Show/hide table
 | |
| Illustration 1 | g01287194 |
- Install O-ring seals (20) onto check valve assembly (9) .
Show/hide table
 | |
| Illustration 2 | g01287180 |
- Install O-ring seals (19) onto bypass valve assembly (8) .
- Install O-ring seals (18) onto fitting (7) .
- Install O-ring seals (17) onto solenoid valve assembly (6) .
Show/hide table
 | |
| Illustration 3 | g01287177 |
- Install O-ring seal (16) onto fuel temperature sensor (5) .
Show/hide table
 | |
| Illustration 4 | g01287165 |
- Install O-ring seals (15) onto check valve assembly (4) .
- Install fittings (14) , nipple assembly (13) , check valve assembly (12) , plug (11) , and fittings (10) onto fuel filter base assembly (2) . Tighten check valve assembly (12) to a torque of 27 ± 3 N·m (20 ± 2 lb ft).
Show/hide table
 | |
| Illustration 5 | g01287121 |
- Install check valve assembly (9) onto fuel filter base assembly (2) . Tighten check valve assembly (9) to a torque of 27 ± 3 N·m (20 ± 2 lb ft).
Show/hide table
 | |
| Illustration 6 | g01287116 |
- Install bypass valve assembly (8) onto fuel filter base assembly (2) .
- Install fitting (7) onto fuel filter base assembly (2) .
- Install solenoid valve assembly (6) onto fuel filter base assembly (2) . Tighten solenoid valve assembly (6) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
- Install fuel temperature sensor (5) onto fuel filter base assembly (2) .
Show/hide table
 | |
| Illustration 7 | g01287027 |
- Install check valve assembly (4) onto fuel filter base assembly (2) . Tighten check valve assembly (4) to a torque of 27 ± 3 N·m (20 ± 2 lb ft).
- Install fuel priming pump (3) and the gasket onto fuel filter base assembly (2) .
- Install coil assembly (1) onto fuel filter base assembly (2) . Tighten coil assembly (1) to a torque of 20 ± 2.5 N·m (15 ± 2 lb ft).
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Install".
Caterpillar Information System:
C15 On-Highway Engine Fuel Filter Base - Disassemble
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fan (Flywheel Cabinet)
C175-16 Locomotive Engine Fuel Injector
3606 and 3608 Engines Aftercooler - Remove
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Fuse Status Indicators
2006/07/10 The Flywheel Groups have Changed {1156}
2013/08/21 A New Pressure Sensor and Buffer are Used {1408, 1917, 191W, 7400}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys SKiiP Interface PWA
3512C Engine for Caterpillar Built Machines Start/Run/Stop Switch
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050} Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
3612 and 3616 Engines Cylinder Head
3606 and 3608 Engines Exhaust Manifold - Remove and Install - 3608
C175-16 and C175-20 Generator Set Engines Air Inlet and Exhaust System Operation
3612 and 3616 Engines Cylinder Head Valves
3606 and 3608 Engines Aftercooler - Disassemble
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Specifications - Modbus Register Map
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Assembly
3512C Engine for Caterpillar Built Machines Starting Motor System
C175-16 Locomotive Engine Aftercooler
2006/07/10 A Cylinder Head Gasket was Reinstated {1124}
2006/07/24 A New Cylinder Head Gasket is Used {1124}
TA22 Transmission Relief Valve - Remove and Install - Cooler Relief Valve
3606 and 3608 Engines Aftercooler - Assemble
C175-16 Locomotive Engine Valve Mechanism