Exhaust Manifold - Remove and Install - 3608
Start By:
- Remove the exhaust manifold shields. Refer to Disassembly and Assembly, "Exhaust Manifold Shield - Remove and Install".
- Disconnect the thermocouples from the segments of the exhaust manifold that are being removed.
- Remove the adapters, if necessary.
- Loosen bolts (1) that mount exhaust manifold (2) to the cylinder head from the segment of the exhaust manifold that is on the end. Loosen bolts (3) that mount the segment of the exhaust manifold that is on the end to bellows (4). Loosen bolts (5) that mount bellows (4) that is on the end to the adjacent exhaust manifold.
- Repeat Step 1 through Step 3 for the remaining segments of exhaust manifold (2). Move toward the turbocharger when you are loosening all of the remaining bolts.
- Return to the segment of the exhaust manifold that is on the end. Attach a suitable lifting device to the segment of the exhaust manifold. The weight of each segment of exhaust manifold (2) is approximately
25 kg (55 lb) . - Remove bolts (1) that mount exhaust manifold (2) to the cylinder head from the segment of the exhaust manifold that is on the end. Remove bolts (3) that mount the segment of the exhaust manifold that is on the end to bellows (4). Remove the segment of exhaust manifold (2). Remove the gasket. Remove bolts (5) that mount bellows (4) that is on the end to the adjacent exhaust manifold. Remove the bellows.
- Repeat Step 5 and Step 6 for the remaining segments of exhaust manifold (2). Move toward the turbocharger when you are removing all of the remaining bolts.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 1 | g01286511 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 5P-3931 | Anti-Seize Compound | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not preassemble the exhaust system before installation of the engine. Damage to the bellows could result. |
- Apply Tooling (A) to the threads of the bolts of the exhaust manifold, the washers, the bolts of the bellows, the plugs and the adapters before installation.
Show/hide table
Illustration 2 g01286511 - Attach a suitable lifting device to a segment of the exhaust manifold. The weight of each segment of exhaust manifold (2) is approximately
25 kg (55 lb) . Position the gasket and exhaust manifold (2) on the cylinder head. Install bolts (1) that mount the exhaust manifold to the cylinder head. Tighten the bolts finger tight.Note: Do not tighten these bolts to the torque specification at this time.
- Repeat Step 2 for all segments of exhaust manifold (2).
- Install bellows (4), bolts (5), and bolts (3) on the exhaust manifold. Tighten the bolts finger tight.
- Tighten bolts (1) that mount exhaust manifold (2) to the cylinder head to a torque of
135 ± 20 N·m (100 ± 15 lb ft) . - Tighten bolts (3) and bolts (5) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - If the adapters were removed, tighten the adapters to a torque of
200 ± 25 N·m (150 ± 20 lb ft) .
End By:
- Install the exhaust manifold shields. Refer to Disassembly and Assembly, "Exhaust Manifold Shield - Remove and Install".
Caterpillar Information System:
3606 and 3608 Engines Exhaust Manifold - Remove and Install - 3606
3512C Engine for Caterpillar Built Machines Emergency Stop Switch
2006/07/03 The Stud Tensioner Tool Groups for 3600, C280, and G3600 Engines Require Different Hydraulic Pressures {0703, 0705, 1100, 1202, 1203}
3508B, 3512B, and 3516B High Displacement Generator Sets Air Shutoff Damper - Remove/Check
3512C Engine for Caterpillar Built Machines Electrical Power Supply
3512C Engine for Caterpillar Built Machines Cat Data Link
3512C Engine for Caterpillar Built Machines CAN Data Link
3512C Engine for Caterpillar Built Machines Analog Sensor (Active)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Inverter Assembly
G3516C and G3516E Gas Engines Engine Speed Sensor
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 525 - FMI 9
2006/08/21 New High Efficiency Oil Filters are Now Available {1308}
3612 and 3616 Engines Cylinder Head
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050} Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
3512C Engine for Caterpillar Built Machines Start/Run/Stop Switch
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys SKiiP Interface PWA
2013/08/21 A New Pressure Sensor and Buffer are Used {1408, 1917, 191W, 7400}
2006/07/10 The Flywheel Groups have Changed {1156}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Fuse Status Indicators
3606 and 3608 Engines Aftercooler - Remove
C175-16 Locomotive Engine Fuel Injector
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fan (Flywheel Cabinet)
C15 On-Highway Engine Fuel Filter Base - Disassemble
C15 On-Highway Engine Fuel Filter Base - Assemble