Fuel Filter Base - Disassemble
Disassembly Procedure
Start By:
- Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove coil assembly (1) from fuel filter base assembly (2) .
Show/hide table
Illustration 1 | g01287027 |
- Remove fuel priming pump (3) and the gasket from fuel filter base assembly (2) .
- Remove check valve assembly (4) from fuel filter base assembly (2) .
- Remove fuel temperature sensor (5) from fuel filter base assembly (2) .
- Remove solenoid valve assembly (6) from fuel filter base assembly (2) .
Show/hide table
Illustration 2 | g01287116 |
- Remove fitting (7) from fuel filter base assembly (2) .
- Remove bypass valve assembly (8) from fuel filter base assembly (2) .
- Remove check valve assembly (9) from fuel filter base assembly (2) .
- Remove fittings (10), plug (11), check valve assembly (12), nipple assembly (13), and fittings (14) from fuel filter base assembly (2) .
Show/hide table
Illustration 3 | g01287121 |
- Remove O-ring seals (15) from check valve assembly (4) .
Show/hide table
Illustration 4 | g01287165 |
- Remove O-ring seal (16) from fuel temperature sensor (5) .
- Remove O-ring seals (17) from solenoid valve assembly (6) .
Show/hide table
Illustration 5 | g01287177 |
- Remove O-ring seals (18) from fitting (7) .
Show/hide table
Illustration 6 | g01287180 |
- Remove O-ring seals (19) from bypass valve assembly (8) .
- Remove O-ring seals (20) from check valve assembly (9) .
- Remove O-ring seals (21) from check valve assembly (12) .
Show/hide table
Illustration 7 | g01287194 |
Caterpillar Information System:
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fan (Flywheel Cabinet)
C175-16 Locomotive Engine Fuel Injector
3606 and 3608 Engines Aftercooler - Remove
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel DC Bus Fuse Status Indicators
2006/07/10 The Flywheel Groups have Changed {1156}
2013/08/21 A New Pressure Sensor and Buffer are Used {1408, 1917, 191W, 7400}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys SKiiP Interface PWA
3512C Engine for Caterpillar Built Machines Start/Run/Stop Switch
Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050} Procedure for Filtering Final Drives, Rear Axles, and Differentials on Caterpillar Machines {0680, 0768, 3258, 3260, 4050}
3612 and 3616 Engines Cylinder Head
3606 and 3608 Engines Exhaust Manifold - Remove and Install - 3608
3606 and 3608 Engines Exhaust Manifold - Remove and Install - 3606
C15 On-Highway Engine Fuel Filter Base - Assemble
C175-16 and C175-20 Generator Set Engines Air Inlet and Exhaust System Operation
3612 and 3616 Engines Cylinder Head Valves
3606 and 3608 Engines Aftercooler - Disassemble
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Specifications - Modbus Register Map
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Flywheel Assembly
3512C Engine for Caterpillar Built Machines Starting Motor System
C175-16 Locomotive Engine Aftercooler
2006/07/10 A Cylinder Head Gasket was Reinstated {1124}
2006/07/24 A New Cylinder Head Gasket is Used {1124}
TA22 Transmission Relief Valve - Remove and Install - Cooler Relief Valve
3606 and 3608 Engines Aftercooler - Assemble