Engine Oil Pump - Assemble
装配步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| B | 1P-0529 | 手柄 | 1 |
| 1P-0468 | 驱动板 | 1 | |
| 1P-0465 | 驱动板 | 1 | |
| C | 1P-0462 | 驱动板 | 1 |
| 1P-0461 | 驱动板 | 1 | |
| 1P-0529 | 手柄 | 1 | |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 根据下列规格，使用工具 (C) 将轴承 (18) 安装到泵体 (8) 上：
- 将轴承 (18) 在泵体 (8) 内侧放置到位，轴承斜面朝向泵体外侧。
- 确保泵接头的角度为 30° ± 15°（从中线穿过轴承孔）。 确保接头朝向泵出口油道。
- 出口油道在轴承孔之间的地方有一个槽。
Show/hide table
 | |
| 图 1 | g01940294 |
Show/hide table
 | |
| 图 2 | g01940736 |
- 根据下列规格，使用工具 (C) 将轴承 (17) 安装到盖 (11) 上。
- 将轴承 (17) 在盖 (11) 内侧放置到位，轴承斜面朝向盖外侧。
- 确保轴承接头的角度为 30° ± 15°（从中线穿过轴承孔）。 确保接头朝向泵出口油道。
- 出口油道在轴承孔之间的地方有一个槽。
Show/hide table
 | |
| 图 3 | g01940293 |
Show/hide table
 | |
| 图 4 | g00480381 |
- 在安装发动机机油泵前，检查所有发动机泵零件的情况和规格。
- 在发动机机油泵的所有零件中使用清洁发动机油。
- 安装压力安全阀 (13) 和螺栓 (14) 。
Show/hide table
 | |
| 图 5 | g01939558 |
- 在泵体 (8) 上安装轴组件 (10) 和轴组件 (9) 。
- 在泵体 (8) 上安装 O 型密封圈 (15) 、盖 (11) 、螺栓 (12) 和螺栓 (16) 。
- 在轴上安装驱动齿轮 (5) 。
Show/hide table
 | |
| 图 6 | g01939557 |
- 在驱动齿轮 (5) 上安装垫圈 (6) 和螺栓 (7) 。
- 使用工具 (B) 将轴承安装到怠速齿轮 (4) 内。 确保轴承的怠速齿轮 (4) 外表面平坦。
- 安装惰齿轮 (4) 。
- 安装进油喇叭口 (3) 、锁紧螺母 (1) 和螺栓 (2) 。
Show/hide table
 | |
| 图 7 | g01939556 |
注: 在安装发动机机油泵前，油泵中必须有润滑油，油泵必须自由转动。
End By: 安装发动机机油泵。
Caterpillar Information System:
2009/06/08 New Window Washer Tank Group is Available for Certain Wheel Tractor-Scrapers {7306}
C7.1 Industrial Engine Electronic Control Wiring Group - Aftertreatment Regeneration Device
Installation of the Payload Monitoring System in Certain Wheel Loaders {7494} Installation of the Payload Monitoring System in Certain Wheel Loaders {7494}
Rework Procedure To Update the Radiator Group{1353, 7251} Rework Procedure To Update the Radiator Group{1353, 7251}
C15 and C18 Tier 4 Final Engines General Information
C7.1 Industrial Engine Exhaust Combustion (ARD) - Aftertreatment Regeneration Device
C7.1 Industrial Engine Fuel Manifold (ARD) - Aftertreatment Regeneration Device
973D Track-Type Loader Hydraulic System Lift Cylinder
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
2009/06/15 New Fasteners for the Valve Mechanism Cover {1107, 1120}
2009/08/17 A New Baffle, A New Bracket, and New Seals Are Now Available On Certain Wheel Tractor-Scrapers {1353, 7251}
973D Track-Type Loader Power Train Pivot Bar
2009/06/08 New Power Train Software is Now Used {7620}
2009/07/06 An Improved Friction Disc for the Torque Converter Impeller Clutch on 988G Wheel Loaders {3101, 3102}
Installation and Initial Start-Up Procedure for G3500B and G3500J Engines {1000} Installation and Initial Start-Up Procedure for G3500B and G3500J Engines {1000}
973D Track-Type Loader Hydraulic System Lift Cylinder
973D Track-Type Loader Hydraulic System Tilt Cylinder
D6T Track-Type Tractor Hydraulic System Lift Cylinder (Bulldozer)
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Power Train Transmission Planetary
2009/06/15 Improved Hardware and Software for the Impeller Clutch on the 993K Torque Converter {1365, 3004, 3067, 3101, 4800, 4808, 7610, 7620}
Undersized Front Track Roller Frame Bearing{4151} Undersized Front Track Roller Frame Bearing{4151}
C9.3 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C15 and C18 Tier 4 Final Engines Lubrication System
2009/10/01 A New Gasket and Hardware Are Used for the Water Lines In Some 3500 and G3500 Engines {1052, 1380}