Transmission Oil Pump - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Bracket | 1 |
| B | - | Guide Stud
M10 x 1.5 by 4 inch |
2 |
- Install gear (12) and gasket (13). Install nut (11). Tighten nut (11) to a torque of
110 ± 14 N·m (81 ± 10 lb ft) .Show/hide table
Illustration 2 g01483233 Show/hide table
Illustration 3 g01481354 - Install Tooling (B). Attach Tooling (A) and a suitable lifting device to transmission oil pump (9). The weight of transmission oil pump (9) is approximately
33 kg (72 lb) . Raise transmission oil pump (9) into position. Install transmission oil pump (9). Install bolts (10).Show/hide table
Illustration 4 g01481330 - Install elbow (8) and bolts (7). Install clamp (6). Connect hose assemblies (4) and (5).
Show/hide table
Illustration 5 g01481294 - Slide hose (2) from tube assembly (3) and onto the elbow that was previously installed. Tighten clamps (1).
- Fill the pump drive with oil. Refer to Operation and Maintenance Manual, "Transmission Oil - (Change)".
Show/hide table
| |
| Illustration 1 | g01483117 |
End By:
- Install the rear drive shaft. Refer to Disassembly and Assembly , "Drive Shaft (Rear) - Remove and Install".
- Raise the guard for the transmission. Refer to Disassembly and Assembly , "Power Train Guard (Transmission) - Remove".
Caterpillar Information System:
Proper Assembly Sequences for Installing Air Inlet Heater Relay (12VDC Relay: 175-2301 Magnetic Switch, 24VDC Relay: 148-0757 Magnetic Switch){1090, 1408} Proper Assembly Sequences for Installing Air Inlet Heater Relay (12VDC Relay: 175-2301 Magnetic Switch, 24VDC Relay: 148-0757 Magnetic Switch){1090, 1408}
854K Wheel Dozer Hydraulic System Location of Electrical Components
992K Wheel Loader and 854K Wheel Dozer Power Train Electrical Output Components
973D Track-Type Loader Power Train Recoil Spring - Assemble
854K Wheel Dozer Machine Systems Push Arms and Blade - Remove
973D Track-Type Loader Power Train Recoil Spring - Disassemble
Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290} Parts to Replace in the Event of Hydraulic Lock or Piston to Valve Contact{1000, 1102, 1216, 1225, 1250, 1290}
C4.4 and C6.6 Engines for Caterpillar Built Machines Ether Starting Aid - Test
D5R Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
D6N Track-Type Tractor Window Washer Reservoir - Fill
992K Wheel Loader and 854K Wheel Dozer Power Train Electrical Input Components
D6N Track-Type Tractor Transmission Oil Level - Check
C4.4 and C6.6 Engines for Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
D6N Track-Type Tractor Fuel System Third Filter - Replace
854K Wheel Dozer Machine Systems Push Arms and Blade - Install
854K Wheel Dozer Hydraulic System Torque Converter Stall and Implement Pump Double Stall - Test
D6N Track-Type Tractor Fuel System Primary Filter (Water Separator) - Replace
D6N Track-Type Tractor Fuel System Primary Filter/Water Separator - Drain
993K Wheel Loader Power Train Relief Valve (Torque Converter Outlet) - Remove
973D Track-Type Loader Machine Systems Fuel Tank - Remove
973D Track-Type Loader Machine Systems Fuel Tank - Install
993K Wheel Loader Power Train Relief Valve (Torque Converter Outlet) - Install
D6N Track-Type Tractor Fuel System Secondary Filter - Replace
D5R Track-Type Tractor Ripper Tips