Relief Valve (Torque Converter Outlet) - Remove
Start By:
- Lower the guard for the transmission. Refer to Disassembly and Assembly , "Power Train Guard (Transmission) - Remove".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the transmission oil to a level that is below relief valve (2) for the torque converter into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Transmission Oil - Change". Relief valve (2) for the torque converter is located on the front right side of the pump drive. Disconnect harness assembly (3). Remove bolts (1) and relief valve (2).
Show/hide table
Illustration 2 g01483955 - Remove O-ring seals (4) from relief valve (2).
Show/hide table
| |
| Illustration 1 | g01483953 |
Caterpillar Information System:
D6N Track-Type Tractor Fuel System Primary Filter/Water Separator - Drain
D6N Track-Type Tractor Fuel System Primary Filter (Water Separator) - Replace
854K Wheel Dozer Hydraulic System Torque Converter Stall and Implement Pump Double Stall - Test
854K Wheel Dozer Machine Systems Push Arms and Blade - Install
D6N Track-Type Tractor Fuel System Third Filter - Replace
C4.4 and C6.6 Engines for Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
993K Wheel Loader Power Train Transmission Oil Pump - Install
Proper Assembly Sequences for Installing Air Inlet Heater Relay (12VDC Relay: 175-2301 Magnetic Switch, 24VDC Relay: 148-0757 Magnetic Switch){1090, 1408} Proper Assembly Sequences for Installing Air Inlet Heater Relay (12VDC Relay: 175-2301 Magnetic Switch, 24VDC Relay: 148-0757 Magnetic Switch){1090, 1408}
854K Wheel Dozer Hydraulic System Location of Electrical Components
992K Wheel Loader and 854K Wheel Dozer Power Train Electrical Output Components
973D Track-Type Loader Power Train Recoil Spring - Assemble
854K Wheel Dozer Machine Systems Push Arms and Blade - Remove
973D Track-Type Loader Machine Systems Fuel Tank - Remove
973D Track-Type Loader Machine Systems Fuel Tank - Install
993K Wheel Loader Power Train Relief Valve (Torque Converter Outlet) - Install
D6N Track-Type Tractor Fuel System Secondary Filter - Replace
D5R Track-Type Tractor Ripper Tips
854K Wheel Dozer Hydraulic System Piston Pump Cutoff Pressure (Hydraulic Fan) - Test and Adjust
854K Wheel Dozer Hydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
Procedure to Install 315-6307, 315-6310 Coupler Lines Groups on Certain Wheel Loaders{5057, 5147, 5734, 6129, 7332} Procedure to Install 315-6307, 315-6310 Coupler Lines Groups on Certain Wheel Loaders{5057, 5147, 5734, 6129, 7332}
3500 Petroleum Engines and Petroleum Generator Sets Configuration Parameters
993K Wheel Loader Power Train Modulating Valve (Torque Converter Lockup Clutch) - Remove
854K Wheel Dozer Machine Systems Lift Cylinder Mounting - Remove and Install
993K Wheel Loader Power Train Modulating Valve (Torque Converter Lockup Clutch) - Install