Control Valve (Tilt Regeneration) - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
注: 使用润滑剂润滑用要密封的密封件。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将工具 (A) 和适当的起吊设备连接到控制阀 (6) 上。 控制阀 (6) 的重量约为 50 kg (110 lb)。
Show/hide table
图 1 | g01446623 |
- 安置控制阀 (6) ,然后安装螺栓 (5) 。
- 连接线束组件 (8) 和卡箍 (7) 。
- 连接管组件 (2) 和卡箍 (3) 。 连接软管组件 (1) 和 (4) 。
Show/hide table
图 2 | g01446618 |
End By: 分离转向机架锁。 请参考 拆解和组装, "转向机架锁 - 分离和连接"。
Caterpillar Information System:
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Remove
854K Wheel Dozer Service Brake Wear Indicator - Check
2008/01/21 New O-Ring Seal and an Improved Cover for the Diverter Valve {5066, 5304}
992K Wheel Loader and 854K Wheel Dozer Power Train Oscillating Axle (Rear) - Install
992K Wheel Loader and 854K Wheel Dozer Steering System High Pressure Screen Group (Deluxe Filtration)
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0590 - FMI 09
2008/01/07 Rubber Pads on the Stops for the Steering Have Been Improved {4304, 7188}
993K Wheel Loader Engine Supplement Alternator - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0585 - FMI 08
993K Wheel Loader Power Train Wheel Bearings - Adjust
992K Wheel Loader and 854K Wheel Dozer Power Train Location of Power Train Components
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Disassemble
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Assemble
AD55B Underground Articulated Truck Power Train Drive Shaft (Upper) - Remove and Install
AD55B Underground Articulated Truck C27 Engine Supplement Bottom Guard (Engine) - Remove and Install
993K Wheel Loader Engine Supplement Engine - Remove
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Remove
993K Wheel Loader Electrohydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
994F Wheel Loader Pump Drive (Rear) from Engine - Separate
992K Wheel Loader and 854K Wheel Dozer Steering System Gear Pump (Steering Oil Cooler) (Steering Pilot)
2007/12/31 A New Calibration Procedure is Now Available {4269}
2008/01/28 New Driveline Components Improve Service Life of Wheel Loaders {3253, 3267}
992K Wheel Loader and 854K Wheel Dozer Braking System Brake System Troubleshooting