Control Valve (Tilt Regeneration) - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 138-7575 | 连杆支架 | 2 |
开始:
- 连接转向机架锁。 请参考拆解和组装, "转向机架锁 - 分离和连接"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
注: 在所有软管、所有软管组件、所有线束及所有管组件上作出识别标记，以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏，并有助于防止污染物进入系统。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前，应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 断开软管组件 (1) 和 (4) 。 断开管组件 (2) 和卡箍 (3) 。
Show/hide table
 | |
| 图 1 | g01446618 |
- 断开线束组件 (8) 和卡箍 (7) 。
Show/hide table
 | |
| 图 2 | g01446623 |
- 将工具 (A) 和适当的起吊设备连接到控制阀 (6) 上。 控制阀 (6) 的重量约为 50 kg (110 lb)。
- 拆下螺栓 (5) 和控制阀 (6) 。
Caterpillar Information System:
854K Wheel Dozer Service Brake Wear Indicator - Check
2008/01/21 New O-Ring Seal and an Improved Cover for the Diverter Valve {5066, 5304}
992K Wheel Loader and 854K Wheel Dozer Power Train Oscillating Axle (Rear) - Install
992K Wheel Loader and 854K Wheel Dozer Steering System High Pressure Screen Group (Deluxe Filtration)
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0590 - FMI 09
2008/01/07 Rubber Pads on the Stops for the Steering Have Been Improved {4304, 7188}
993K Wheel Loader Engine Supplement Alternator - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0585 - FMI 08
993K Wheel Loader Power Train Wheel Bearings - Adjust
992K Wheel Loader and 854K Wheel Dozer Power Train Location of Power Train Components
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Install
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Disassemble
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Assemble
AD55B Underground Articulated Truck Power Train Drive Shaft (Upper) - Remove and Install
AD55B Underground Articulated Truck C27 Engine Supplement Bottom Guard (Engine) - Remove and Install
993K Wheel Loader Engine Supplement Engine - Remove
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Remove
993K Wheel Loader Electrohydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
994F Wheel Loader Pump Drive (Rear) from Engine - Separate
992K Wheel Loader and 854K Wheel Dozer Steering System Gear Pump (Steering Oil Cooler) (Steering Pilot)
2007/12/31 A New Calibration Procedure is Now Available {4269}
2008/01/28 New Driveline Components Improve Service Life of Wheel Loaders {3253, 3267}