Control Valve (Tilt Regeneration) - Assemble
组装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
注: 检查 O 形密封圈、垫片和密封件有无磨损或损坏。 如有必要,请更换部件。
注: 使用润滑剂润滑用要密封的密封件。
- 安装阀 (24) 、轴承 (23) 、弹簧 (22) 、O 形密封圈 (21) 和塞 (20) 。 安装杆 (25) 。
Show/hide table
图 1 | g01447072 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 使用适当的压力机压缩弹簧 (19) 。 将弹簧 (19) 、护圈 (18) 、挡圈 (17) 安装到壳体 (10) 上。
Show/hide table
图 2 | g01447074 |
Show/hide table
图 3 | g01447073 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装滑阀 (15) 、O 形密封圈 (14) 、定位销 (13) 、盘 (12) 和螺栓 (11) 。 安装接头 (16) 。
Show/hide table
图 4 | g01447032 |
- 将弹簧 (9) 、线圈组件 (8) 、垫圈 (7) 、O 形密封圈、销 (6) 和芯组件 (5) 安装到壳体 (10) 上。 拧紧芯组件 (5) 至扭矩为 35 ± 3 N·m (26 ± 2 lb ft)。
Show/hide table
图 5 | g01446978 |
- 安装歧管 (2) 和螺栓 (1) 。 对其余歧管重复此步骤。
Show/hide table
图 6 | g01446973 |
- 安装执行器 (3) 和螺栓 (4) 。
End By: 安装控制阀。 请参考 拆解和装配, "控制阀(倾斜再生)- 安装"。
Caterpillar Information System:
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Disassemble
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Install
992K Wheel Loader Machine Systems Control Valve (Tilt Regeneration) - Remove
854K Wheel Dozer Service Brake Wear Indicator - Check
2008/01/21 New O-Ring Seal and an Improved Cover for the Diverter Valve {5066, 5304}
992K Wheel Loader and 854K Wheel Dozer Power Train Oscillating Axle (Rear) - Install
992K Wheel Loader and 854K Wheel Dozer Steering System High Pressure Screen Group (Deluxe Filtration)
C15 and C18 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0590 - FMI 09
2008/01/07 Rubber Pads on the Stops for the Steering Have Been Improved {4304, 7188}
993K Wheel Loader Engine Supplement Alternator - Remove and Install
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0585 - FMI 08
AD55B Underground Articulated Truck Power Train Drive Shaft (Upper) - Remove and Install
AD55B Underground Articulated Truck C27 Engine Supplement Bottom Guard (Engine) - Remove and Install
993K Wheel Loader Engine Supplement Engine - Remove
992K Wheel Loader and 854K Wheel Dozer Power Train Trunnion Support (Oscillating Axle, Front) - Remove
993K Wheel Loader Electrohydraulic System Piston Pump Margin Pressure (Hydraulic Fan) - Test and Adjust
994F Wheel Loader Pump Drive (Rear) from Engine - Separate
992K Wheel Loader and 854K Wheel Dozer Steering System Gear Pump (Steering Oil Cooler) (Steering Pilot)
2007/12/31 A New Calibration Procedure is Now Available {4269}
2008/01/28 New Driveline Components Improve Service Life of Wheel Loaders {3253, 3267}
992K Wheel Loader and 854K Wheel Dozer Braking System Brake System Troubleshooting
2008/02/11 The Improved Software for the Autolube {7540, 7610, 7620}
994F Wheel Loader Pump Drive (Rear) to Engine - Connect