Transmission Oil Filter - Replace
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
- 操作机器使液压油预热。
- 将机器停放在平地上。 把铲斗降到地面,并施加轻微的压力。 接合停车制动器,然后关闭发动机。
Show/hide table
图 1 g01271357 - 变速箱加注口的检修门位于驾驶室平台中间的驾驶室后面。 打开检修门。
Show/hide table
图 2 g01271358 - 卸下螺栓 (1),然后拆下盖 (2)。
- 取出旧滤清器滤芯。 妥当弃置用过的滤清器。
- 安装新滤清器滤芯并更换盖。
- 安装盖及 5 颗螺栓。
- 对于其它滤清器,重复步骤 4 至步骤 7。
- 关闭检修门。
Caterpillar Information System:
D10T Track-Type Tractor Machine Systems Fast Fill Fuel Adapter
D7G Series 2 and D7G Series II Track-Type Tractors Safety Messages
D7G Series 2 and D7G Series II Track-Type Tractors Operator Controls
D6G Series 2 Track-Type Tractor Operator Controls
3508 EUI Engine for Off-Highway Truck/Tractors Muffler
525C, 535C and 545C Wheel Skidders Machine Systems Solenoid Valve and Manifold (Parking Brake Control) - Assemble
525C, 535C and 545C Wheel Skidders Machine Systems Solenoid Valve and Manifold (Parking Brake Control) - Disassemble
525C, 535C and 545C Wheel Skidders Machine Systems Solenoid Valve and Manifold (Parking Brake Control) - Install
525C, 535C and 545C Wheel Skidders Machine Systems Solenoid Valve and Manifold (Parking Brake Control) - Remove
Modes of Failure for Quick Disconnect Connectors {0618, 5057, 6129} Modes of Failure for Quick Disconnect Connectors {0618, 5057, 6129}
D6G Series 2 Track-Type Tractor Hydraulic System Bulldozer Tilt and Ripper Control Valves
525C, 535C and 545C Wheel Skidders Engine Supplement Air Cleaner - Remove and Install
854K Wheel Dozer Transmission Oil Level - Check
D6N Track-Type Tractor Hydraulic System Angle Cylinder (Bulldozer)
D6N Track-Type Tractor Hydraulic System Lift Cylinder (Ripper)
525C, 535C and 545C Wheel Skidders Power Train Transmission - Disassemble
525C, 535C and 545C Wheel Skidders Power Train Transmission - Assemble
D6N Track-Type Tractor Hydraulic System Piston Motor (Steering)
854K Wheel Dozer Transmission Oil Sample - Obtain
854K Wheel Dozer Cooling System Coolant Level - Check
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Install
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Remove
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Install