Flywheel - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 5/8 - 18 UNF x 11 in     |
2     |
- 拆下两个螺栓 (1) 。 将工具 (A) 安装在曲轴中。
Show/hide table
图 1 | g01220437 |
Show/hide table
图 2 | g01220438 |
- 拆下剩余的螺栓 (1) 。 在工具 (A) 上将飞轮 (2) 滑离发动机。
- 将适当的起吊设备连接到飞轮 (2) 上。 飞轮 (2) 的重量约为 130 kg (285 lb)。 拆下飞轮 (2) 。
- 如有必要,使用液压锤和冲头,将齿圈 (3) 从飞轮 (2) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 5/8 - 18 UNF x 11 in     |
2     |
B     | 6V-4876     | 润滑剂     | -     |
- 加热齿圈 (3) 。 将齿圈 (3) 安装在飞轮 (2) 上。
Show/hide table
图 3 | g01220438 |
Show/hide table
图 4 | g01220437 |
注: 安装齿圈 (3) 的时候必须让轮齿斜面一侧朝上。 当飞轮安装完毕之后,轮齿斜面一侧应朝向起动马达。
- 将工具 (A) 安装在曲轴中。
- 将适当的起吊设备连接到飞轮 (2) 上。 飞轮 (2) 的重量约为 130 kg (285 lb)。 将飞轮 (2) 定位到曲轴上。
- 将工具 (B) 涂抹在螺栓 (1) 的螺纹上。
- 安装螺栓 (1) 。 拆下工具 (A) 。 安装其余的螺栓 (1) 。
- 拧紧螺栓 (1) 至扭矩为 100 ± 5 N·m (75 ± 4 lb ft)。 再转动螺栓 180 ± 5 度。
- 检查飞轮跳动。 请参阅测试与调整, "飞轮 - 检查"。
Caterpillar Information System:
320D and 323D Excavators Machine System Specifications Front Lines
C7 Urban Transit Bus Engines Exhaust Particulate Filter Indicator - Check - Diesel Particulate Filter (DPF) Diagnostic Module
Inspecting the Turbocharger for Exhaust Leaks{1052} Inspecting the Turbocharger for Exhaust Leaks{1052}
C15 and C18 Industrial Engines Engine Oil Pan
C27 and C32 Generator Set Engines Gear Group (Rear) - Install
C15 Industrial Engine Sensors and Electrical Connectors
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Travel Motor - Assemble
2005/11/21 Improved Joint Assemblies and Seals are Used for the Fuel Lines Group {1274}
C11 and C13 Engines Flywheel
C11 and C13 Engines Flywheel
TH31-E61 and TH35-E81 Petroleum Transmissions Specifications
CX38-P892 Well Servicing Transmission Electrical Storm Injury Prevention
C15 and C18 Petroleum Engines Engine Oil Pan
C27 and C32 Generator Set Engines Crankshaft Rear Seal - Remove
C27 and C32 Generator Set Engines Crankshaft Rear Seal - Install
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Electronic Modular Control Panel 3 (EMCP 3)
2011/11/16 A New Connecting Rod Is Used in 3500B and 3500C High Displacement Engines {1218}
2005/11/14 New Aftercoolers are Now Used {1063}
C7 Urban Transit Bus Engines Monitoring System
C27 and C32 Generator Set Engines Flywheel Housing - Remove and Install
C15-XQ400 Rental Generator Set Plate Locations and Film Locations
C15 and C18 Industrial Engines Vibration Damper
2005/12/12 New Flash File on C18 Marine Engines {7620}
330D and 336D Excavators Leaving the Machine